WRS26MR4JS1 Crosley Refrigerator - Instructions

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

What would have been a simple job I made hard by pulling the water hose out of its place that was the hardest part about putting the ice dispenser back in, it took me about thirty minutes to put it back I !

The website said 60% of people with same refrigerator problem solved the problem with a new fan kit. I received the fan kit within 3 days of ordering. Was shipped from Fresno, CA to Long Beach, WA. The fan kit was to be installed behind rear panel in the freezer compartment. When I removed the old fan motor, I noticed the shaft turned harder than the new fan motor, suggesting a problem with the old fan motor. I plugged in the obvious fan motor power bundle with no problem. The instructions and diagram with the kit nearly steered me wrong. Instructions, diagram and splices with the kit instructed to cut the "extra" wire bundle and splice "similar" wires (should have said same color wires). Luckily, I ignored those instructions when I remembered the U-Tube video depicted the extra wire bundle was to be inserted into a factory penetration in the back panel, facing the freezer compartment. This power bundle is for adding an ice maker, which my refrigerator did not have. When reassembled and the refrigerator restarted, I could immediately feel forced air in the refrig, where there was no flow before fixing. I observed that all the refrig and freezer dials do is act like a valve to increase or decrease air flow to the compartments. The dials have no mechanical or electrical connections, just designed to divert air flow from across the cold 'evaporator' fins. I recommend other consumers to remember carefully what they see in the video and watch again if stumped during the job. The video was better than the instructions which may have been written in China or India. I am happy. Repair was a lot cheaper than a new refrigerator and I would not have bought another Frigidaire. Thanks to this website. r. andersen

Open door - popped it in - done

pulled the old seals off one at a time and starting from the top of each door, pressed the top edge of the seal into the groove, using the quik clamps to hold the top in palce at each top corner, went down each side of the door and pressed the seal into the groove, when I reached the bottom, I moved the clamps to the bottom and used thm to help press the seal into the bottom groove, Each door took about 15 min.

Fixing the meat drawer slides was really easy and I got it fixed in a snap. What I wanted to tell you was that I ordered the wrong bins twice and your customer service person was just great she got me the wright bin and made returning the wrong parts very easy. I would like to complement her on her service.

Simply removed old bearing with the pliers and aligned new beating into the socket.

Just set the new shelf over the clips on the door. VERY easy.

followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.

Replaced

The repair was very easy, just a matter of snapping the bin on the door. However, i was very please and impressed with the expeditious service that i received. I ordered the door around noon and it was delivered by 10am the next day. This is what i consider "quality service" and I thank this company sincerely.

A part replacement. I was extremely happy to find the somewhat obscure part at Parts Select and at a very reasonable price. The part arrived in three days and fit perfectly. Very satisfied!!!

Replaced old bins with new .Fit like a glove and seemed to be of better material. Delivered with-in a couple of days. Thanks

not much to putting a bin in just insure it is in clips correct and your done.what I was amazed with was the ease of getting correct cut sheet to order part and no drawn out 2 page forms to become a member and it arrived ups which is not always easy in alaska and was on my door step when we got back from a week trip out snowmachining. this was the most accurate and easiest part I have ever ordered, and I work on the supervision end of construction and spend so much wasted time ordering over the internet when I have to

I ordered a extra bin for the door. I ordered the wrong one the top bin and the bottom two are made different. I didn't notice that. The person I talked to was very kind and helpful. Also I have never received a product as fast as from this company. Great service. Thank you.