WDB635RBS0 Westinghouse Dishwasher - Instructions

remove front lower cover , and place a towel under drain pump to catch water , shut breaker off to kill power , then with a right angled phillps screw drive you can remove pump screws and slide pump out after hoses have been removed also you need to remove 2 of the screws holding the top of the pump mount and the 3 rd leave lose pump comes out and you reverse the steps ' dishwasher ' does not have to be pulled out and turned on its back , a short phillps screw driver is needed and a right angle phillips also .

I replaced the spray arm that had melted with the new one The fix took a minute and the dishwasher no longer leaks

I woke up on Christmas Day to water pooling under the kitchen sink (I guess I made the naughty list last year). Upon inspection, I could see that the water connections for the faucet were damp. Since I had all the parts, I replaced the faucet and service lines. Once complete, there were no leaks so I turned on the dishwasher to double check for leaks in those lines. It was all dry when the dishwasher finished but the next morning, more water under the sink.
I proceeded to replace the water line to the dishwasher and ran it through another wash cycle. Still leaking.
I found PartsSelect online and order a new drain line for the dishwasher. To my amazement, FedEx dropped off my order the next morning........yes, the next morning.
It took five minutes to remove the old drain line and install the new one (just a worm clamp at each end). It would have been faster than that but I don't get up and down as fast as I use to.

I took out the old dishwasher rack, slid in the new one. Nothing else was done and my spouse thought I had built her the Taj Mahal. Many repairs are nothing but cosmetic; the hard part is finding the model number and getting it ordered.

removed 2 screws holding door skin on. removed 6 screws holding dispenser unit in door. Removed 2 color coded wires. Removed old dispenser, cleaned area for new dispenser. installed 6 screws on new dispenser and connected 2 color coded wires. Re-installed door skin and secured with the 2 screws. Job took all of 10 minutes . Part fit correctly no leaking and is working great.

Watched a video on the website and did it exactly the same

Removed the old gasket and slid in the new one. Very easy.

Lower rack was simple R&R. It was about 1" lower height than original but I suppose it fits multiple apps. Upper rack removed from slide rails with clips removed with fingernails. The funnel & spray arm came off by hand but the old rack had rusted under the snap-on clips on the funnel mount base causing stretching & a loose fit on new rack. I drilled a 1/8" hole in the base & used a small plastic zip-tie to secure the base to the rack. Problem solved. No other tools needed besides the drill & it took longer to go to garage to use it than all else combined. Still about a 10 minute task. Under 1 beer in red-neck repair time.

Remove six screws from upper door to expose the latch.Remove two screws from latch.Remove four wires from the switch.Install wires to switch and reinsert screws to latch and door.From the time I ordered the part,to the time the dishwasher was running again was less than one day,thanks to fast delivery.Fast and easy.

Turned off water and power! Couldn't move dishwasher out, so access was a little problem. Worked to disconnect inlet hose. Finally unscrewed the whole unit, disconnected the outlet hose and the power connection and then unscrewed the unit from the inlet hose. Removed the ell from old unit, applied Teflon tape, and screwed it into new unit. (Tighten it really well. I didn't and had to take things apart again!) Installed new unit starting with the inlet tube, then the outlet tube then the frame screws. Turned water and power back on and tested the dishwasher. SUCCESS! My wife thinks I'm a hero.

I'm a girl and it was pretty simple. I pulled out the dishwasher, removed the bottom plate cover. Removed the water line to the inlet valve and made sure the water was getting to the valve (it was). Removed the electical connector from the valve. Removed the valve and installed the new one. Made sure the water was pumping into the dishwaser. Pushed the dishwasher back into place. Runs great.

I took the replacement rack out of the box. Then I removed the old rack out of the dishwasher and put the new one in. It was that easy.

Removed old rack and discarded it rolled new one in/complete

The best advice I can give is to watch the repair videos; they are very well done and demonstrate exactly what to do. I played them a couple of times (particularly for the upper rack) and the replacement was exactly as described...very easy. The "close up" shots were very helpful.

This not was very easy to install I have to remove the fron panel of the dishwasher to see were to insert the new gasket i you instruction how to instal this was insert the new gasket from the rigth side to the left well if you look the front of the diswasher you insert from the lefth in to the place how hold the gasket inplase was not very esy to install but was don and working OK.