Models > W30400B Maytag > Instructions

W30400B Jenn-Air Oven - Instructions

All installation instructions for W30400B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the W30400B
31-45 of 227
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven getting 50 degrees or more, hotter than setting

  • Customer: Joseph from Wappingers Falls NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Display light on clock/temp control dimmed

  • Customer: Larry A from Fayetteville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
Piece of cake. First, turn off the power to the stove. Then, I removed four hex head screws on the bottom (above the oven door) and four phillips screws underneath the burner knobs (knobs pull right off). The entire assembly then came loose and I laid it facedown on the stove top. The clock control was easily accessible. I unplugged two electrical connections and a ribbon which "unplugs" easily by squeezing the ends and pulling up on the ends. Only two hex head screws hold the clock assembly and I removed them.

Then, it was only a matter of reversing everything I had done. The new clock light is brilliant.

Oven kept shutting off, getting F-3, F-5 messages on LED readout

  • Customer: ken from north andover MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
I was out pricing new stoves. Why are slide in stoves twice the price of regular stoves?? I tried one last go at ordering part, overnight mail. Needed to get it fixed for the holiday meal. Part came within one day, early, and it worked. Stove fixed easily, spent the money on a big screen TV.

lcould not see the lights on the clock or temperature on the control panel

  • Customer: charlette from FREDERICKSBURG TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
The parts came with no instructions, we started to take off , the front panel , finally took off the 4 screws under the panel, then the two small ends caps on either side. the only problem we had after being carefull to study the part as we took it off , was the ribbon strip, that stayed connected to the stove. after we tried to put all back together, the exhaust fan kept coming on. There are two small
holes that need to be aligned in the replacement part. also to get the strip out and back in you need to press and pull up on the small black notches on either of the strip.

Broiler blement failed

  • Customer: Donald from Hudson NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 11 people found this instruction helpful
Sunday, four days before Thanksgiving, our oven would not bake properly. A quick check indicated the top element was not working. What to do? Where to get a part in time to fix for Thanksgiving dinner? The answer was easy - PartSelect. I had the part in my hands on Tuesday AM. Oven was fixed in 15 minutes and my wife was baking pies within an hour. All worked well and yes, we had a wonderful trukey dinner. Great service !

Self cleaning would not work on the oven

  • Customer: Crucita from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 9 people found this instruction helpful
Removed old part with a pair of pliers and plugged the new part into place.

Very simple and the self cleaning feature works again.

When opening the oven door, the hinge on the left of the door broke.

  • Customer: Louise from Cedar Rapids IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
We panicked cause even simple repairs on these products cost and cost.....but we remained calm and ordered the exact part necessary from you. It arrived in just 3 days and once we had the part in hand it was easy to understand how to replace it. We disassembled the door with screwdrive and swapped the broken part with the new one. The one gotcha was that we were not aware of the shipping pin holding the spring and we struggled for a few trying to get the door closed all the way. Once we discovered the pin and removed it, it was fixed and we were PLEASED!

Thank you,
Louise and Rickl

Oven light stays on when door is shut.

  • Customer: ALAN from OSWEGO IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.

Oven would not heat

  • Customer: Robert from Baldwin NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 5 of 7 people found this instruction helpful
At first I called a repairman. He said I needed a relay board replaced but that it was no longer being made. I found this needed relay board on PartSelect.com. Once I received this board within a few days, the repairman returned to install this for me. However, as it turned out he simply removed the old board only to put the same board back in by being careless. When the oven still wouldn't heat he said we should try another part. I said no to this. After he left I determined that the new relay board hadn't been installed but simply looking at it. I then installed this new board myself and the oven now works properly. Who needs these so called "professional repairman" who overcharge, are irresponsible and make you wait hours for their "service".

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

lighted display very dim to non existant

  • Customer: Dan from Burlington IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Thanks to JP in customer service.

TURN THE POWER OFF TO THE STOVE at the breaker box!
I had to pull all the burner knobs off (4ea) and remove the screw under each one. Then open the oven door and remove the screws holding a trim piece on and the hex head screws holding the "touch pad panel" on (was also held on by the screws I had already removed from behind the knobs) 1 smaller screw at each end (total of 2) under there hold the plastic trim on that needs to be moved slightly to let the panel come out. (DON'T OVER TIGHTEN WHEN YOU REASSEMBLE) You hang the panel in the 2 slots provided and remove the old display unit. Gently unplug the 2 wire harnesses and ribbon that actually connect the touch panel to the display PC board. Look for the 2 small holes in the ribbon that will line up with the female part on the board. A piece on the board where the ribbon plugs in will slide up a little and allow you to plug the ribbon in and then push it gently back down. Finish putting it back together and turn power back on at the breaker box. Works perfectly.

Oven door locked and was flashing code F4

  • Customer: Mary L. from Trinity TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

Self Cleaning did not work.

  • Customer: Rick from Beaverton OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 4 of 5 people found this instruction helpful
Remove burner knobs, Removed 7 screws from bottom of face plate. Removed screws from 2 alluminum or steel spacers I guess you could call them. I let the Op Panel hang carefully not to stress wires. I marked all wires of the Latch asm. Removed the four screws holding it in and carefully removed the wires. Replaced in opposite manner and self cleaning works. The oven tried to start the cycle but I noticed the latch never triggered. When the function first stopped working I was able to apply slight force to the door and the latch fired. So after replacing the door switch it still failed to work. So latch asm was the official fix. So I have had to replace the latch asm and the Op Panel for being dim. I don't think this model is very good. But Partselect.com is great easy to find parts and good prices. Very pleased with my experience.

Lightning zapped oven clock control assembly.

  • Customer: John from Corpus Christi TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Had estimates of $ 500.00+ to replace clock assembly. Purchased it at parts select for approx $ 200.00 and put it in myself. Will pocket the $ 300.00. Thanks. Turn breaker to stove off. Removed four screws underneath front panel. Must open oven door to access screws. Tilted the panel out from the bottom allowing the top of the panel to come out. Had to remove the two knobs on either side of the clock along with the clock knobs. When the two knobs on the side are removed it releases the mounting brackets for the clock inside the panel. Replaced clock assembly wires one at a time. Reassembled in reverse procedure.

The Old Hinges broke off and the door would not stay closed

  • Customer: Bruno from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.
All Instructions for the W30400B
31-45 of 227