2084278-1-S-Whirlpool-74006613-Oven Relay Control Board
2084278-1-S-Whirlpool-74006613-Oven Relay Control Board 2084278-2-S-Whirlpool-74006613-Oven Relay Control Board

Oven Relay Control Board

PartSelect Number PS2084278

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • Compare At

    $302.83
  • You Save

    $50.47
  • Your Price

    $252.36
In Stock
Recycling Rebate Available
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 3 reviews What's this?
1-3 of 3
 

9 of 10 people found this instruction helpful

Parts Used

  • Oven Relay Control Board

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerWILLIAM from RICHMOND TX

Constant beeping with error displayed; started during self-cleaning; could not reset

Very simple.

First, TURN THE POWER OFF AT THE BREAKER BOX!

Unscrew the (built-in) oven from the wall / cabinet (4 screws). Unscrew the cover in front at top where the LED display is held, and pull it back, then pull two sets of wires off of the LED display PCB, so it can be put aside. Pull the oven out of the cabinet, sit it on a chair (because the 240V power feed metal cable is still attached). Unscrew the 7 1/4th-inch hex head screws holding the metal top cover on; remove the cover, which exposes the wires and sensors, etc. Unscrew the "relay board" PCB (1 screw) and detach it from the side, leaving all wires attached to the terminals. Then, one by one, remove the wires from the old PCB and attach them to the corresponding terminal on the new, replacement PCB. Screw the new PCB back onto the side of the oven top inside, screw the top metal cover back on, attach the wires to the front panel LCD and then screw the front panel back on. Push the oven back into the hole in the cabinet and screw it into the wood on the side and bottom (6 screws total).

Finally, turn the power back on (flip the circuit breaker on). Then observe: your oven is now no longer a digital boat anchor!

The only reason it took me longer than 30 minutes to finish this was that I had to recruit someone to help me lift the oven out of its cabinet. After doing so, however, I realized that I could have done it all by myself, simply by sliding it out onto a box or chair, but I didn't realize that ahead of time. It's not really that very heavy (but I would not recommend anyone who's not strong trying to do it alone, regardless). Anyway, if I had to do it again, it would only take about 10-15 minutes to accomplish.

The part itself colst about $180. When my usually very reasonably-priced appliance repairman quoted a price of $450 to $500 to do this repair, even after I told him specifically which part was obviously bad (which he would have to order or pick it up), I decided that only an idiot would be unable to do this repair by himself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

  • Oven Relay Control Board

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerRobert from Baldwin NY

Oven would not heat

At first I called a repairman. He said I needed a relay board replaced but that it was no longer being made. I found this needed relay board on PartSelect.com. Once I received this board within a few days, the repairman returned to install this for me. However, as it turned out he simply removed the old board only to put the same board back in by being careless. When the oven still wouldn't heat he said we should try another part. I said no to this. After he left I determined that the new relay board hadn't been installed but simply looking at it. I then installed this new board myself and the oven now works properly. Who needs these so called "professional repairman" who overcharge, are irresponsible and make you wait hours for their "service".

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 21 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerJames from Bryan TX

Oven wouldn't heat.

The repair was a simple exercise in throwing the fuse, removing 2 screws, and a 1 for 1 replacement of the connections for wiring. We turned on the power, and Viola it was an oven, and not a digital boat anchor.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3