Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF326FBB > Instructions

TEF326FBB Tappan Range - Instructions

All installation instructions for TEF326FBB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FBB
511-525 of 664
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No current to the burner

  • Customer: terry from Pensacola, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Broken inner glass panel in oven

  • Customer: GARY from LIBERTY, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Bought a electric range/oven with a broken glass in the door cheaply because the owner didn't think they could fix the glass. I watched the video on You Tube on how to handle the spring loaded hinges and followed the steps as presented. The toughest part of the job was cleaning all the crud on all of the glass due to the gap in the inner glass. I had to use a square drive and a phillips head screwdriver to disassemble and reassemble the door. It took less than 30 minutes to complete the job and most of that time was cleaning the glass.

Burners on high all the time.

  • Customer: Randy from Van, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced control units that were malfunctioning.

Element broke in two

  • Customer: NICOLLE from EADS, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My husband fixed it in about 30 minutes or less. He said it was a piece of cake!

baking element burnt out

  • Customer: Deborah from Deatsville, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It was so easy. We pulled the stove away from the wall and unplugged it. My husband used a nutdriver to unscrew the two screws holding the element in place. He unplugged the wires from it when he pulled it out. He plugged the wires to the new element, screwed it back in place and voila! I was ready to bake. So very easy.

broken bake element

  • Customer: MICHAEL from POINT PLEASANT, WV
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
nothing to it

the stove eye would go to high and stay

  • Customer: ronnie from cana, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Lower heat element quit working

  • Customer: Donna from Taylorville, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Undid two screws; removed old element; inserted new element and placed the bracket and two screws to hold in place.

Needed to replace the bottom heating element in my oven

  • Customer: Ilene from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I watched the video--that was very, very helpful. My son helped me, but I think I might have been able to handle it without him after watching the video. Also, your price was far less than half of what another website quoted for the same heating element.

Oven not heating

  • Customer: Steve from lake Hiawatha, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed oven from wall, disconnect power source, loosen nuts from element, pull element out, disconnect wires, hook up wires to new element, put back nuts.Plug in and it worked great.

No heat from bottom or top element,k stove top and clock all worked fine.

  • Customer: steven from Daleville, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

Bake element burnt out

  • Customer: Elizabeth from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Disconnected power; unscrewed element from oven wall; pulled element off of contacts. Pushed new element onto contacts; screwed to oven wall

Bake element caught fire and stopped working

  • Customer: Megan from Savannah, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
After in I found my oven glowing from the small fire inside, I thought I was in for an expensive repair or complete replacement. Part select helped me find the exact part I needed and the video showed me just how easy it would be. $40 and 15 min later my oven was fixed and I was baking again! The repair consisted of removing two screws and simply removing and plugging in the new bake element. Thanks for the help!!

Oven Temperture probe.

  • Customer: Kenneth from Edgemount, SD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

oven element not working

  • Customer: Patricia from Hendersonville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old element and just popped in the new one
All Instructions for the TEF326FBB
511-525 of 664