PSS26SGRBSS General Electric Refrigerator - Instructions

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.

Watch to step by step video instructions on your site. Great service! Part arrived the following day after order!

This is a manufacturer design defect with this model refrigerator. The plastic washer that holds the auger strips the washer until it just doesn't work. There is no real repair, we are shipped a new one, take the old Ice Bucket out and put in the new one. No effort what-so-ever. If they made the plastic washer, a metal washer it would forever eliminate the problem. Part Service however is an excellent supplier. They can handle the problem very well and send the cost back to the manufacturer. Problem is this is going to strip and have to be replaced often.

It was exactly as shown in your instruction video

The thermostat was set at 0 for the freezer, but at 37 for the refrigerator. The refrigerator was showing a temperature of 20 degrees and would not stay at 37. After learning the 3 choices it could be (air inlet cover, thermostat, and computer), I went for the air inlet on the basis of percentage of repair. With this particular refrigerator with this problem; this is repair has the highest chance of success. Nice on-line decision making tool! I went with choices of previous buyers and followed previous buyers instructions. All I needed was a couple of Phillips head screw drivers, and cleaning the dirt I was finding in the refrigerator was the biggest job.

Removed power, removed control panel cover, removed control board, installed new control board.

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

When I clicked on the part to see it's description the pop up window included a youtube video on how to install the part. The video was right on the mark. Very easy installation. Phillips screwdriver was the only tool needed. Repair performed in less than 15 minutes. I have used this site before and it has been extremely helpful in saving me money by doing the repairs myself instead of paying an arm and a leg for a repairman to do it.

We had been told at some point the main control board would need replacement, due to various system issues with the refrigerator. The total repair cost would have been close to $400. The cost of the board was less than half of that cost. The instructions provided by PartSelect were very good. There was also a video of a similar model of refrigerator that outlined and showed every thing step by step. I removed the screws from the access panel in the back of the unit. unplugged the electrical plugs, removed the board. Installed the new board, reinstalled the plugs (all were idiot proof as PartSelect indicated), reinstalled the access panel and plugged the refrigerator back in. It has worked like new since install. This is an excellent website and service. I will use it again as needed with all my appliances.

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

Removed the cover installed parts. Parts were very simple cover was a major problem. Instructions stated "simply remove cover by pushing on cover and clips will release" They dont and cover broke.

Took out old, inserted new. Less than 5 minutes. Easy to find part on website. Quick delivery.

Removed lower back grill panel with 5/16th nut driver, removed water valve with nut driver, removed inlet water line with adjustable wrench, removed two water oulet lines by pushing in bushings and pulling on water lines by hand. installed new water valve and attached water lines, secured new valve to back of fridge and re-attached back panel.

Used your, diagnostic chart,whatched associated video and replaced thermostat. Easy , simple and cheap!!! I am thrilled with the website and service you provide. I definately will be back for more repairs as they arise. THANK YOU !!!!!

Took out the old and put in the new one...Water is back on!