Models > PSS26SGRBSS

PSS26SGRBSS General Electric Refrigerator - Overview

Get Parts and Repair Help for PSS26SGRBSS

If you know the refrigerator repair part you need, you can browse the list of all parts on the PSS26SGRBSS, or you can search by name or part description. You can also find your part by where it is located on the PSS26SGRBSS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for PSS26SGRBSS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.82

Light Bulb - 40W

Sold individually.

$9.20

Temperature Sensor

Also known as Thermistor. This part is used to sense the temperature in the cabinet.

$46.00

Dual Inlet Water Valve

This double outlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

$10.25

Defrost Thermostat

This part acts as a safety device against over heating in case of mechanical failure.

$151.68

Main Electronic Control Board

This board controls the operation of the unit. Note: This part has been updated by the manufacturer. It may differ in appearance but will function the same as the original.

$62.79

Ice and Water Filter

Sold individually. NOTE: As per the manufacture this is an updated water filter. If you have never installed the updated filter or your old filter was made by Culligan, you may need the adapter to install the filter. GE Refrigerator Water Filter. If you have never installed this new style filter or your old filter was made by Culligan you may need the adapter to install it.

$31.30

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

$6.20

Dispenser Door Assembly or Flapper

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appliance.

$144.30

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$27.55

Ice Dispensing Drive Cup

This part is found at the end of the auger in the ice container - replace this part when the icemaker doesn't dispense ice.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigertor water dispenser not working BUT ice machine is working

  • Customer: ralph from bristow VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 496 of 542 people found this instruction helpful
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and pr... read more

The refrigerator made continous "whooing" sounds that increased and decreased in pitch. Sounded like a ghost. Would keep us up at night. Also noticed that the heater was not heating under the evaporator coils.

  • Customer: John from Holly Springs NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 274 of 302 people found this instruction helpful
After checking the stories, the consensus of opinion was to change the mother board. I had a tremendous help from Tom Paone at quality@applianceeducator.com. He also told me to change the motherboard but to make sure that the coils were totally defrosted before starting up the refrigerator after changing the board.

Took off three nuts around the b... read more

Fridge too warm, evaporator icing up

  • Customer: Gerald from San Clemente CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 167 of 196 people found this instruction helpful
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wir... read more