PHS69EHSS3 Frigidaire Refrigerator - Instructions

All I had to do was put the bin-door into place...it couldn't have been simpler.

1) cleared remaining parts of broken crisper supports by pushing them into refrigerator insulation(pushed on 'pegs' so 'peg' holes in side of plastic inner liner of refrigerator were clear. 2) Was unable to fully place new crisper supports into postiion. 3) Then, out of despiration, used small light hammer to gently tap on largest 'pin.' I was surprised to see this 'pin' enter into plastic side of refrigerator and then to see crisper support was secure when 'pin'/peg' was flush with new crisper support. 4) then returned crisper to correct postion; supports held. 5) WARNING-DO NOT OVERLOAD CRISPERS!! I BELIEVE THIS CAUSED 'PIN'/'PEG' FAILURE INITIALLY! I don't know if cause was volume too high with crisper forced into place OR if the crisper mass/weight was the culprit. SUGGEST weight limit less than 7.5 lbs.; don't attempt to load in more volume than top of crisper.

I first determined the problem. I found PartSelect.com through online search. I ordered the part online Sunday morning. Part arrived Tuesday afternoon(Christmas eve) and I installed it that night! Now I am a gal mind you, but I am pretty handy. I pulled out the fridge, unplugged it and removed the back panel, easy. Then I used a heat gun on low the defrost the 'defroster' which had REALLY iced up bad. It had iced up so much,in fact, it had disconnected the evaporator fan connection. I clipped the wires. Stripped the ends, slid on the shrink tubing supplied, connected the wires with the crimp connectors and heated the shrink tube. I also put another piece of shrink tube on the fan connector so it would be more secure. Put the panel back on, plugged it back in and started working like a champ!! I am so proud of myself and likely saved at least $250.00 on a service call! Total cost for this repair, $22.00!! :D

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

I slipped the Bin In the slot and pushed in on the side clips and it was done The only problem was the Package was very light and the wind blew it away. 1 Block luckily the neighbor found me and brought it over.

unplugged the old one and pushes in the new one DONE IN LESS THAN 6 Min.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

just snapped it in - 1 minute repair

I removed the food on the door and placed it in the refrigerator. I placed a plastic sheet over the opening of the refrigerator to keep the cold air in. Then I removed the bracket for the upper hinge, remover the door and placed it onto a table. Then I removed the plastic bearing from the bottom of door. I then replaced it with the new bearing. Then I removed the lower bearing and its bracket from the refrigerator. At this point I had to modify the new lower bracket by removing the alignment tab with a dremel because there wasn’t any hole in the housing for it. Then I attached the new bracket and bearing. Replaced the door and upper hinge and the job was complete. It took only about a half an hour to finish.

Pretty simple installation. I carefully removed labeling from old Dispenser Cover & pressed onto new Cover. Unscrewed electronic green board compartment from back, loosened stays, inserted new Ribbon Cable Harness (got this backwards initially, so had to redo it), repositioned stays. Screwed electronic green board compartment onto new Dispenser Cover, inserted other end of Ribbon Cable Harness into door slot & attached Dispenser Cover to door. AND IT WORKS! My first attempt at frig repair.

I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

Just popped back on.

popped old one out...new one in...easy

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

Snap the new one in