PHS69EHSS3 Frigidaire Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
not freezing, refrigerator not cooling, back of freezer icing up
I first determined the problem. I found PartSelect.com through online search. I ordered the part online Sunday morning. Part arrived Tuesday afternoon(Christmas eve) and I installed it that night! Now I am a gal mind you, but I am pretty handy. I pulled out the fridge, unplugged it and removed the back panel, easy. Then I used a heat gun on low the defrost the 'defroster' which had REALLY iced up bad. It had iced up so much,in fact, it had disconnected the evaporator fan connection. I clipped the wires. Stripped the ends, slid on the shrink tubing supplied, connected the wires with the crimp connectors and heated the shrink tube. I also put another piece of shrink tube on the fan connector so it would be more secure. Put the panel back on, plugged it back in and started working like a champ!! I am so proud of myself and likely saved at least $250.00 on a service call! Total cost for this repair, $22.00!! :D
Parts Used:
-
Mary K from Bristol, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The refrigerator's In-door water dispenser leaked water. The leakage started out slow and over a period of time increased.
This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.
Parts Used:
-
Frank from Mentor, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Broken door bins
I slipped the Bin In the slot and pushed in on the side clips and it was done The only problem was the Package was very light and the wind blew it away. 1 Block luckily the neighbor found me and brought it over.
Parts Used:
-
Janet from Smithville, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dirty water filter
unplugged the old one and pushes in the new one DONE IN LESS THAN 6 Min.
Parts Used:
-
Michael from CANTON, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no water flowed to the ice maker
1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.
Parts Used:
-
Levern from Mc Donald, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
clear tray broke
-
Richard from Houston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
"Popping" noise when opening the refrigerator door.
I removed the food on the door and placed it in the refrigerator. I placed a plastic sheet over the opening of the refrigerator to keep the cold air in. Then I removed the bracket for the upper hinge, remover the door and placed it onto a table. Then I removed the plastic bearing from the bottom of door. I then replaced it with the new bearing. Then I removed the lower bearing and its bracket from the refrigerator. At this point I had to modify the new lower bracket by removing the alignment tab with a dremel because there wasn’t any hole in the housing for it. Then I attached the new bracket and bearing. Replaced the door and upper hinge and the job was complete. It took only about a half an hour to finish.
Parts Used:
-
Alan from Plantation, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Condensation rusted screws, caused plastic Dispenser Cover to break & fall out, which pulled out & broke Ribbon Cable Harness, so ice & water dispenser did not work.
Pretty simple installation. I carefully removed labeling from old Dispenser Cover & pressed onto new Cover. Unscrewed electronic green board compartment from back, loosened stays, inserted new Ribbon Cable Harness (got this backwards initially, so had to redo it), repositioned stays. Screwed electronic green board compartment onto new Dispenser Cover, inserted other end of Ribbon Cable Harness into door slot & attached Dispenser Cover to door. AND IT WORKS! My first attempt at frig repair.
Parts Used:
-
LINDA from BRADENTON, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
refer quit cooling and so did freezer
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
Parts Used:
-
jerry from petaluma, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
one milk shelf cracked inadvertently and the lower door shelf broke when removing
-
EMILY from EIGHTMILE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
plastic bottom door bin cracked and broke
-
Tom from Brant Lake, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice Maker Not Getting Water
Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.
Parts Used:
-
Edward from Cuba, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
broken door bin
-
Pat from Cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old Filter Was Dirty Slid It Out
-
JERRY from LIBERTY CENTER, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Our refrigerator ice maker was broken, crisper draw was broken, and shelf support was broken.
We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle
Parts Used:
-
Gary from North Smithfield, RI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!