Models > NAV3335AWW > Instructions

NAV3335AWW Amana Washer - Instructions

All installation instructions for NAV3335AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the NAV3335AWW
76-90 of 357
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Pressure switch was bad, not working

  • Customer: Edwin from Eagar,, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
Removed screws form back of console cover, removed bad pressure switch, Installed new, repeated steps in reverse order.

Loud squeal when spin cycle finished, white powder under washer

  • Customer: Kevin from Pooler, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 5 of 5 people found this instruction helpful
Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

Agitator was loose and wouldn't stay in place

  • Customer: Myrtle from HYES, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 5 of 5 people found this instruction helpful
First I removed the bolt and removed the old agitator and post assembly then I put the new agitator and post assembly in place and tightened the bolt. It was so easy, when I called the manufacturer they wanted to send out a technician, but thanks to Parts Select I fixed the problem without spending alot of money and without the hassle.

Noticed nick in drive belt durng inspection and cleaning

  • Customer: Brian from Plainville, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
Washer was making noise especially when spinning. I took the washer apart to clean it, That is what it really needed. Also adjusted the water level to prevent overflows which caused soap and water to get underneath into the drive belt area as well. During inspection noticed a nick in the drive belt, Although this was not really causing immediate problem wanted to repalce it to prevent problems. Ordered the belt; it came in two days with no special postage. To install, just leaned the washer over on its front on a slight incline. Took old belt off and put new on by turning the big pulley. It is spring tensioned, so no tools. This may be the easiest part repacement I ever did. Took longer to write this paragraph than to repalce the belt.

new belt worn out by a bad motor pulley

  • Customer: ALBERT from WASCO, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.

washer was squeeling to a stop

  • Customer: paul from newbern, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

Leaking Water Pump

  • Customer: Edwin from Eagar,, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.

Cold water no fill

  • Customer: Christopher from Cincinnati, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
Always check the basics first!

Mistakenly replaced the water valve (even though it was buzzing idicating it had power and showed 110V across terminals). Assumed the water lines were working. Turned out to be a clogged cold water line (safety valve clogged). Replaced both lines for good measure, machine working fine.

Water wouldn't shutoff. Agitator would pop up and stop agitating

  • Customer: James from South Jordan, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Opened up washer, found vacuum hose was broken and replaced it. Removed agitator with a couple extensions and a socket wrench. Found agitator part was worn out and replaced it. The best part was how great PartSelect made it so incredibly simple and easy to find the right part. I'm now a customer for life. Kudos PartSelect.

Front legs came off while moving causing cycle pulley to rub on the floor.

  • Customer: Jerry from Dayton, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 24 people found this instruction helpful
Removed damaged pulley installed new pullley and clutch. The directions made it easy. Aligned pulley as detailed and installed new front feet and tested washer. Took me about 30 minutes to repair. Washer has been working since. Thanks guys for a nice no nonsense package.

water was not going to the barrel

  • Customer: HAMID from CHATSWORTH, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 4 of 4 people found this instruction helpful
first I thought there is a problem with with hoses.problems like filter or hoses blocked.after I opened the hoses they were fine .Water was going out with power .Then I opened the valve connected to the hoses . I checked these hoses withe help of a 12 volt battery . the valve was not opening so I came to the conclusion that this part is broke.is not easy to change this part.Small place and hard to unlock the hose inside .They could design this much easier with just using longer hose.But I think then nobody will call service dept.

Topside door would not remain in an open position; lid hinges worn out.

  • Customer: James from Oakland, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!

The washer was making a fine squeeling noise that created a foul burning odor

  • Customer: SONY from CONCORD, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

White fluffy residue appeared under washer. Unbalanced banging during spin cycle

  • Customer: John from Blue Bell, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

washer got off balance almost every load.

  • Customer: keith from auburn, AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 4 of 5 people found this instruction helpful
i followed the directions i found online. do not take the screws all the way out! The snubber ring solved the problem. I replaced the springs since i had them. The old ones seemed OK.
All Instructions for the NAV3335AWW
76-90 of 357