MFI2568AES Maytag Refrigerator - Instructions

I simply took the drawers and bottom glass shelf out and took the two screws that hold the end cap in out, removed the draw slide from it, installed the drawer slide on the new part and put it it. Very easy.

Using a nut driver remove the left side panel and install the replacement part. Most of the time spent was finding the nut driver and removing the food items.

I removed 2 trays and a glass plate. Then removed the broken cap. I removed the tray slide hardware from the broken enc cap and installed it on the new end cap. Then installed the end cap in the refrigerator and replaced the glass plate and 2 trays.

Everything fit properly and the job took about 20 minutes.

I first removed both crisper drawers.You then remove the glass top. With that out of the way you remove the two 1/4 inch screws out of the drawer track, then remove the three screws., be careful whenyou remove the part not to damage the lever contoling the tempeture. You then reverse the procedure. Not hard at all. Thae parts were fantastic. I would recommend the to everyone. Thank you very much.
Charlie.

1. Remove pantry cover and tray assembly.
2. Remove two Crispers above tray.
3. Remove glass and seal in rear.
4. Remove phillip screws, 2 or 3 holding right end cap to refrig body.
5. Pull end cap from wall to the left releasing temp valve from back of frig.
6. Remove side metal slider from end cap.
7. Dissasmble temp valve slider from endcap and rear cap.
8. Remove temp valve control knob and handle from end cap.
9.Put back together in reverse order being careful not to loose the styrofoam seal from hole in rear of frig

It was no surprise that this was an easy repair, but I must say that I was completely impressed that the part was on my door step in 24 hours with STANDARD shipping.

very easy

Remove the drawers above the unit as others have indicated and the glass top and then using a 1/4 inch nut driver remove the screws. Now it gets just a bit tricky as the air control knob under the top is a two peice linkage that is best removed as a single unit being carefull not to break off the tab that rests in the middle back of the refrig. Simply swing it out towards the left as you face it and it will become obvious its just a simple tab and once it clears everything comes out in one unit. The logic holding everything together is simply a matter of squeezing a couple of tabs to remove the back portion then a couple more for the inner right side. Re assemble in reverse order and take the opportunity to give everything a real good cleaning. My time of about 45 minutes included a real good cleaning of all shelves etc....happy new year and thanks parts select for getting the part to me in what i think was next day...Awesome service guys

Simple- I removed the food, drawers, and shelving from the unit. I unscrewed the 2 screws holding the end cap on. Once removed I also separated the sliding track from the old part and put it on the new part. I then screwed the new end cap into place using the same screws as the old one. I put the shelves, drawers, and the food back in. All in less than 10 minutes.

Poped ou the old switch, connected new switch and pushed back into socket.

Replaced Lesf side Pantry End cap. Directions on web site easy to understand.

Removed pantry and glass shelves. Remove three small screws. Pop out end cap and remove drawer rail(two phillips screws). Reinstall on new end cap and place back in refer with three screws. Reinstall glass shelves and pantry. Job complete!!!

Took all the shelves and drawers off above part to be replaced and cleaned them. Removed old part and replaced with new.May I add new part fit perfectly!. No major problems encountered. Tip: remember where all parts were removed from!

really easy it took less than 15 minutes, it took more time to clean out the refer. than to do the repair.

Remove drawers. Remove 1/4 screws. Remove end cap. The linkage for temp control is very fragile so be very careful. Not a very dificult task at all.