LSG2700W Jenn-Air Washer Dryer Combo - Instructions

These Maytag people know how to build stuff. I was impressed with this valve. Built really smart. After a gazillion years (about 16 or so) the valve started making a funny groaning noise and the cold water flow was very slow. Took about 15-20 minutes to fill the tub.

the inlet valve is located on the back of the washer where the hoses are connected. In fact the hose connectors are part of the valve.

To replace this valve, start by unplugging and turning off the water spigots, unscrew the two hoses from the valve. (you need a towel here, but that'll be obvious soon enough.)

Unscrew the single screw at the top of the valve bracket (the bottom of the bracket is held in place without screws.) Remove the screw holding on the sheet metal and pull the bracket out as far as you can without stretching things. Write down what colors of wire are connected, then pull off the electrical connectors.

The valve outlet is a skinny (compared to the inlet hoses) rubber hose that has a clamp to hold it in place. The clamp needs to be loosened with a 3/16" nutdriver a plier would probably work, but may be hard to get in there. Now slide the clamp further up on the hose, dislodge the rubber hose off of the old valve. Now it's free.

Reverse the steps. Believe it or not, that is all. It works great and this washer probably has another 10 year left in it.

Clamp was already in multiple pieces so easy to get off.

Got clamp from partselect.com in 1 day which was great.

Removed two PH screws from front cover then pulled bottom of front cover outward and down to remove.

Caution for those doing this: take a piece of 220 or 240 grit paper and sand all the edges of the clamp. Trying to put it on without doing so will result in countless paper cuts in hands.

Before putting new clamp on be sure to use either some soap or silicon lube on the rubber V seal between upper and lover tub.

Also need to put some 1/4" to 3/8" spacers at three equally spaced places beneath the upper tub and the lower tub. If this isn't done the upper tub will drop down too far inside the lower tub and the inner lower tub, when it starts to spin, will rub on the underside of the upper tub = cause the main drive belt to smoke and tub to "freeze up"

Spacers I used were simply 3 pieces of multi strand sheathed electrical wire 3/8" so that I could bend them down at an angle and put them out once clamp was in place. Wire pieces need to be about 4-5" long.

Assemble one bolt in clamp and thread around tub in CCW direction.

Position one bolt of the clamp in right rear corner. this is important so that when tub goes out of balance, there's clearance for the clamp bolts and they don't contact the cabinet.

Make sure before threading clamp arount tub that the screw that will end up in the front left corner has a hex head on it so that you can apply some clamping "muscle" with a socket wrench.

I had trouble getting the front left screw inserted in the clamp (its only 2" long) so I used a 3" bolt to make the preliminary connection to pull the clamp semi tight. I planned ahead and got a light wire coat hanger to use as a "tie-tie" in the event that I had to remove the 3" slotted screw to revert back to the 2" hex head screw. Luckily when I removed the 3" screw I was able to quickly pop the 2" hex head back in and tighten completely.

Before putting front cover on, do one load with front cover off to make sure that upper and lower/inner tub don't rub each other.

If ok, turn power back off and put front cover back on.

Note: Would advised ordering the rubber V-seal if you are ordreing the clamp. If you buy the seal there are four bolts in the lid that let you lift the lid to work on the tub, clamp and seal MUCH more easily. Sticky part is getting water fill tube in top left rear disconnected so that new rubber v-seal can slide over tub.

Note also that in order to get to front left lid bolt that single bolt holding diaphram onto front left upright must be removed so as the let diaphram assembly drop away to access front left lid bolt. The two bolts in the rear can be accessed from the top very easily. Also need to disconnect the bleach fill tube in order to lift the lid (right side lifts up to vertical position)

I tested the dryer coils and found that they were getting a voltage but would not open the gas valve. Coils were not bad but weak. After they warmed up they would not open the gas valve. It took 10 min to repace both coils and the heat sensor.

Remove top two front cover screws. Disconnect wiring. Set aside front cover - door assembly.

Remove two screws at top of the vertical riser cover to expose entire dryer interior. Remove filter. Remove screws to blower cover plate. Remove 4 screws that fasten front drum guide assembly. Remove drum. remove and replace 2 drum support rollers . Replace one rusted drum roller shaft. Replace both drum rollers and non-metalic washers.

Drill out 4 rivets holding two front drum glides. Replace and rerivet new drum glides.

Pry back slighty the many retention points around the front drum assembly which hold the front drum felt seal. Refit the new front drum felt, pressing the retaining clips back in place with a screwdriver.

Replace tumbler motor belt.

Install Drum. Install front drum retention assembly. Install new blower seal with reassembly of blower cover.

Total time - about 1 hour

I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the front open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++

Replaced the 2 belts according to instructions received with the belts. Very easy repair

Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.

I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.

I was told that it might be a clog in the tube.. we check the tubes that wasn't it Then I Google it and was told it might be the drain pump. I was just glad that Part Select had what I need because my machine is over 20 years old. We change the pump and now I hope I get at least another 20 years out of my machine. I will always use part select to get my parts. Thanks

1. Unplug power to the washer.
2. Remove 2 screws from bottom front panel on either side. Panel then rotates out and unhooks at the top. Remove front panel
3. Remove bolts from underneath the top front on both sides using a socket.
4. Rotate the top upward to provide space to see and work.
5. From the back of the washer, remove 4 bolts using a socket around the drain tube at the upper left.
6. From the front, the siphon valve can be removed from the inside upper right.
7. From the front, unscrew the clamp holding the drain hose on the water pump housing at the bottom right front and remove the hose. Be prepared for water to drain from the hose. Remove hose and siphon valve together and discard.
8. Install new hose on new siphon valve and screw new clamp tight. Make sure the rubber ring is inserted properly on the new valve (See old valve for reference)
9. Holding the siphon valve in place, use a socket and re-attach the 4 bolts around the drain tube at the back of the washer.
10. From the front, insert the opposite end of the new hose to the water pump at the lower right front and screw the circle clamp tight. Note: Re-use existing clamp.
11. Rotate the top back down into normal position.
12. Plug the power back in and run a short cycle and watch for leaks.
13. If no leaks, re-attach bolts for the top with a socket.
14. Re-attach front panel with 2 screws. Done.

The dryer was not getting hot the clothes we're damp and had to put on hangers to finish drying. I pulled the cover plate saw the element was glowing the gas cable would kick on had a flame for about a four to six second count. I did some checking on the web. I read about others who were having same type of problem. Order the limit part and now.the flame stays on for about twenty second or less the dryer gets hot and it drys fast. Thanks for the web site. It took about thirty minutes . Now it works great.

Turned off circuit breaker. Removed two screws at base of front panel with stubby Phillips-head screwdriver. Swung panel up about 30-degrees, and removed panel, disconnecting red and yellow wire to door switch. Removed four sheet metal screws and took off large drum support bracket. Checked drum support rollers and shafts. They were fine. Reset circuit breaker and turned on dryer. Rattling noise still present.
Removed six small screws holding blower fan assembly. Shaft receiver on squirrel cage fan was worn completely round (it should fit onto a half-round shaft). Ordered new blower fan from PartSelect.com. Replaced tonight, and it works beautifully. This dryer is 29-years old. All it's ever needed in the 10-years I've owned it is a belt replacement and this repair. Long live the 1970s Maytags, and good parts suppliers like this one.

Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.

Removed the screws and took the door off then took the front panel off and popped up the top. Then pulled the drum out. Took snap ring pliers and removed rollers and replaced with new rollers then vacuumed all lint from machine and reversed operation to put everything back together. Operation was a total success!

Unplug the dryer and remove the front panel (two screws at bottom of the panel), being careful of the door switch wires attached to the front panel. Using an ohm meter, I checked the ignitor for continuity and found it was open (should be 50-100 ohms). Make sure to check the solenoids on the gas valve. When the igniter goes bad, it will usually burn out the valve 1 solenoid boost coil (the one with 3 terminals), which was the case with my dryer. The solenoid coils are held in by a bracket with two screws (series 01 dryer) and are easy to remove and replace. Be careful replacing the igniter as the heating element is VERY fragile. Take the time to vacuum out all of the accumulated lint and dust inside the dryer while the front panel is removed, including the lint trap and duct. New igniter and boost/hold solenoid fixed the problem.