KGST307FBL0 KitchenAid Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Spark Ignition Electrode was not sparking properly
Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade
Parts Used:
-
Wade from Jacksons Gap, AL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter failer
Very easy, unscrew the old one remove the back panel tie a string to the wires pull though the front of the oven remove the string tie it to the new ingiter and pull the wires back though the oven back wall and hook up the wires and screw it back into place.
Parts Used:
-
STEPHEN from LAPEER, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
We are living in a rental house. The oven was missing a rack, so I called and ordered one.
I think this does not qualify as a repair. I called and ordered the oven rack, it came in the mail and I put it in the oven. Nothing to it.
Parts Used:
-
Pat from Royal Oak, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
hinge would pop out each time the door was closed.
With glass side down:
1. Removed the side panels
2. Removed the bottom panel
Turned over door holding glass in place.
3. Removed outer glass panel
4. Removed handle top
5. Removed top screw holding hinge mechanism
6. Removed screw for spacer and clip holding hinge mechanism
7. Lifted hinge mechanism out and replaced with new part.
Reattached parts and screws in reverse order (6-1)
1. Removed the side panels
2. Removed the bottom panel
Turned over door holding glass in place.
3. Removed outer glass panel
4. Removed handle top
5. Removed top screw holding hinge mechanism
6. Removed screw for spacer and clip holding hinge mechanism
7. Lifted hinge mechanism out and replaced with new part.
Reattached parts and screws in reverse order (6-1)
Parts Used:
-
Les from PARMA, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven light glass cover was broken
took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.
Parts Used:
-
wayne from LIMINGTON, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
left cover for the oven light broke when trying to replace the bulb
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Parts Used:
-
Mark from SHOREVIEW, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clearly, the bulb was the problem. The gasket is an invitation to more trouble.
Simple. But beware changing just the bulb when the gasket is not secure.
Parts Used:
-
James from THE VILLAGES, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spark module failure, wouldn't spark.
The repair was fairly straightforward, much easier the second time around. The first part was defective. (irregular spark). I reordered and installed the new one. It works, but nowhere near as good as the original.The problem is that the frequency of the spark on these replacement modules is only once per second. To get technical, the gas as presented to the spark is turbulent, causing several sparks to occur before the ideal mixture coincides with the spark. Needless to say, there is an excess of gas wafting around the kitchen until it lights, sometimes in excess of 20 seconds. NOT SAFE! Our BBQ and fireplace insert spark orders of magnitude faster than this.
Parts Used:
-
Bob from LAKEWOOD, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
igniter on top right front burner was shorting out,it would click but not ignite burner
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Parts Used:
-
Shelly J from KAPLAN, LA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both left and right door hinges broke off their pins
The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.
Parts Used:
-
Tracy from Thousand Oaks, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
grate pads were gone, making cleaning difficult
-
Christie from Provo, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electrical short from oven light.
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
Parts Used:
-
William H. from morehead city, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
hinge on oven door broken
I have KitchenAid convection oven that is about ten years old . The hinge on the left hand side broke so I had to replace it. It took me about 2 hours to get the job done because I cleaned the door as I went . The change out while fairly strait forward did take some time . A lot longer the some of the people said .
Parts Used:
-
charles from batimore, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
3 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas broiler stopped working
I unscrewed the igniter from the top of the oven, and removed the back panel of the stove. I had a friend in the back while I jiggled the two wires to see which ones they where. Then I had to use two pliers to pull the connectors apart. I tied a string to the two wires and pulled them out through the oven and left the string and tied the new wires to the string and pulled the new wires through the back of the stove, and replaced the back and screws.
Parts Used:
-
Doug from MOUNT VERNON, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Parts Used:
-
JOSEPH from COON RAPIDS, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!