KGST307FBL0 KitchenAid Range - Instructions

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.

cleaned out pad area with an awl. then the pads just slide in.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Removed broken glass cover and bulb, cleaned old gasket off with damp cloth and replaced with new bulb, glass cover and gasket. No tools needed.

Replaced the oven igniter. The most difficult part for me was getting the stove out to gain access to the back. Used sheet metal to guide the rear legs up onto the tile. Used string to guide the wiring to the rear connectors. The rest was easy and it worked.

I didn't. Don't know how to get to light bulb to change it for this specific model

Repair was very straightforward. Based on information gathered from an earlier post about the same repair I simply removed all screws from the oven door. These were all located on the bottom edge of the door itself. Upon removal of the screws the door separated and exposed the "core" where I then had access to the hinges which were held in by one screw each. I removed the broken hinge, replaced it with the new hinge, pieced the door back together, put back all the screws, and the repair was complete.

Remove the cover housing the ignitor. Unscrew the 4 screws to get to the ignitor. Remove two screws to remove the ignitor. Those two screws might be ceased up and will need some excessive force if heads get stripped. Use a needle nose vise grip to remove if you run into this. Once removed, open cover at back of oven. Disconnect the two leads for the ignitor which one will go to the gas control valve and the other will be up towards the top left. Pull ignitor out. Installation is reverse of removal.

had to take the stove out to get the back off to replace the part.

Unscrewed about 10 screws to disassemble the door to get at the hinge then screw new hinge in. Was inspired by the woman who said she did it while watching a child. I saved $200 in the repair fee I was quoted

REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3

Your online video was a great help.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

remove grate - flip upside down - be sure holes are clean and dry - using toothpick, swab some RTV sealant into the holes and a bit on the pads ... insert pads till they seat - be sure to hold in place till all air is evacuated - wipe excess RTV with paper towel...DONE

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.