JSD2789HES Jenn-Air Refrigerator - Instructions

Defrost circuit was inside the control assembly inside the refrigerator so I snapped the two release clamps located to the rear of the assembly (lights and controls). Slid the whole assembly cover off and removed the lightbulbs and two screws right above them. In from of that is the temp switches and directional slider, removed the two screws holding that. With the four screws out, removed whole assembly and laid it dowm on the first shelf, defrost circuit is at the back right, easy change out but take note which way the 4 prong plug fits into the circuit board. Refrigerator was back to normal in about 6 hours.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

Ice door flap was broken and warm air was getting into the freezer. I removed a total of 4 screws to get to the flap. Total time was less than 15 minutes and very easy. Partselect customer service was very helpful and friendly. If you have any questions, do not hesitate to call them. They were very helpful! I have this site bookmarked!

Pull out fridge and unplug
Remove drip tray from dispenseer
Unscrew face plate (star bit) 2 screws
Carefully disconnect wire strap from faceplate controls
Unscrew dispenser from chute - 3 screws and one is hddend next to actuator.
Carefully disconnect another wire strap to remove unit.
Remove actuator pad
Remove limit switch (i small philips screw)
Replace switch & pad
Re-assemble

Neither the actuator pad nor the limit switch appeared broken or worn but it appears to have solved the problem.

Not a terribly complicaed repair but you need to take care not to damage anything as you take apart. More work than just changing a filter or bulb.

Defrosted coils with hair drier and after the freezer was turned back on the freezer cooled to 0 Deg. within 4 hours but coils collocted ice. Checked coil with ohmmeter OK replaced Defrost Assy. Repair was very easy and new replacment unit is sealed and the original is an open curcuit board. thanks for allowing me to share this with you!

This is the 2nd time I replaced the ADC, the freezer condenser was frosting up again and wouldn't keep the freezer or refrig cold. 1st part only lasted 6-months. The simple fact is that the ADC used in the Maytag as well as others is under designed; I purchased 2-this time, 1's a spare, and you know it going to need to be replaced again. Sadly I'm stuck with this Refrigerator for at least 2-years before I buy another, it's only 5-years old. From my experience (with other Maytag products I've purchased recently) I'd never buy another Maytag product, ever! Since Whirlpool bought Maytag, I'm taking Whirlpool off my list too. Thanks Partselect for such a speedy delivery on the part everything back to normal, at least for now, wished I knew how long this ADC will last?

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

Simple to fix. Watched the video and noted what to do.
Replaced the control board, solenoid, and limit switch. Woks like new!

My ice maker was overflowing and i realized that it was the water valve that needed replaced. unscrewed 1 nut, unhooked 3 water lines, unhooked electrical components and re-installed in reverse order. took about 10-15 mins.

I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!

Easy to diagnose problem because there was water to the water dispenser but none to the newly installed icemaker. Originally did attempt to clean the solenoid but found the plunger assembly damaged.

New part arrived sooner than I thought it would. Takes about as much time to remove the lower vent cover as to replace the valve. Remove the electrical plug from the wall, valve off the main water supply, remove lower vent cover, disconnect the supply hose from refrigerator valve assembly, remove one hex head mounting screw and you have both water valves in your hands. Identify the valve the supplies water to the filter and the one that supplies water to the icemaker/water dispenser. Then confirm which plastic water supply line goes to the water dispenser and which goes to the icemaker. Hose diameters are different but it is good to know. Disconnect the plastic water supply lines from both the ice dispenser and the icemaker portions of the valve. Replacement solenoid valve does not have thread on type compression fittings. Snip about an inch off of each hose and then press into the appropriate valve orifice.

Making sure the plastic supply lines do not get crimped, remount the valve assembly, reattach the supply hose, valve on the water and check for leaks. No leaks, reinstall dust cover and plug the refrigerator back in.

Move the unit back in place and then take a long deserved beer out and have a celebratory toast for a job well done.