Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
My wife destroyed the oven door seal with oven cleaner...
I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.
Remove door, racks, unplug, remove lower burner cover two screws, the burner tube deflector pan two wingnuts, the burner tube. With igniter attached, remove back of range 4 screws to expose connector to igniter, unplug then remove burner tube, then igniter, replace igniter feed through back of oven wall and reconnect igniter reverse process and its done
My wife called a service company and was told that a tech would have to inspect the stove. service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00
ignitor was cracked and would no longer light the burner
I removed the burner cap and then the two screws that held the burner in place, pulled it out about 3 inches, disconected the ignitor and pluged the new one in, put the burner back in place and put the two screws back in, replaced the burner cap and it was done. I would also like to mention that I ordered my replacement part on Sunday evening and recieved it on Tuesday morning. Thanks Part Select!!!
I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account
The igniiter is made of ceramic and had cracked. I remove the burner assembly, but couldn't remove the screw holding the igniter. After trying liquid wrench and every available screw driver. I opted to order the complete burner assembly. I installed the new assembly in 5 minutes and it worked great. This is the second ceramic igniter that has cracked on this stove top and both times I've had to replace the whole assembly. For a $1000 stovetop, I expected better quality. I'm just wondering how many times I'm going to have to replace burner assemblies. Each time it's been a different assembly.
I've done this once before on this same gas stovetop as the electrode can degrade if it suffers from too many "boil-overs". The most important thing to do if the 2 screws holding the burner head on the cooktop are "tight" and don't unscrew easily is to soak them with WD-40 to loosen them up. Don't be in a hurry. They may need a couple of soak and waits. Once the screws are out, it's just a matter of connecting the wire on the electrode and replacing the burner. Also a Star screwdriver that fits properly is essential.
glass pane was cracked during the cleaning process
needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks
Blower motor stopped working and the breaker tripped. Horrible smell! from the somewhere in the oven. Looking at the wiring diagram told me that there was a relay board feeding he motor, but I had no idea where it was, which took a little Internet searching to find it. Finally seeing that it was in the rear I was happy to see that there was enough flexible gas line to pull out the stove enough to check the board, which was fried. I replaced the board and then looked for the reason it smoked and found that the blower motor was shorted (and stank horribly). It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent. The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet. Everthing works like a charm now.
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches to disconnect the electric wire - it had a small bayonet connection. I turned the element over and unscrewed the small screw holding the ignitor to the element freeing the ignitor from the element. After receiving the part from Part Select, I reversed the process...
1. attaching the ignitor to the underside of the element using the small screw. 2. reattaching the electric wire to the ignitor. 3. positioning the element on the stove top. 4. reattaching the eelement using the 2 screws. 5. testing and finding it worked fine.
A couple of observations:
1. The screws holding the element to the stove are star screws while the screw attaching the ignitor to the element is Phillips - necessitating 2 different screwdrives for an easy repair.
2. I had problems with the initial part delivery - it went to a wrong address. PartSelect Customer Service was great. I had a less than 5min wait for getting a rep on the line with the 1 call I had to make to get this corrected. And when I did get a rep she was both helpful, friendly and knowledgeable in correcting the situation.
Installing the 2 new burner assemblies worked great with the new screws. New screws however, did not work with the old burner assemblies that have rusted screws I wanted to replace. New burner assemblies are slightly taller that the old ones.
Oven would stop heating after a few minutes of operation
Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.
I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.
I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.
Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!
