1643288-1-M-Whirlpool-715957K-Urethan-Foam-Gasket.jpg
1643288-1-S-Whirlpool-715957K-Urethan-Foam-Gasket.jpg 1643288-2-S-Whirlpool-715957K-Urethan-Foam-Gasket.jpg 1643288-3-S-Whirlpool-715957K-Urethan-Foam-Gasket.jpg

Urethan Foam Gasket

PartSelect Number PS1643288

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $14.54
  • You Save

    $2.42
  • Your Price

    $12.12
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.4 / 5.0, 5 reviews What's this?
1-5 of 5
 

362 of 365 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerJohn from Berkley MI

Blower motor died and I needed to replace it

Most of the repair was obvious as I took the blower apart before ordering the parts. Unfortunately the new motor was significantly larger than the original motor so I had to um. Adjust the position of some of the other parts to fit it in. There was a sheet metal flange that was installed on the other side of the blower from the motor which was designed to focus the air flow into the blower. I used a hammer to ajust the angle of flange so it no longer extended as far into the blower housing.

It works just fine although its a bit louder than the old motor was.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 13 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerLawrence from Chandler TX

High blower vibration

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerRichard from Harrisburg PA

Replace blower motor

disassemble housing and remove fan and motor. Reatach fan to new motor, connect wiring, place gasket around motor and reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerSteven from Marshfield MA

Downdraft blower failure

Blower motor stopped working and the breaker tripped. Horrible smell! from the somewhere in the oven. Looking at the wiring diagram told me that there was a relay board feeding he motor, but I had no idea where it was, which took a little Internet searching to find it. Finally seeing that it was in the rear I was happy to see that there was enough flexible gas line to pull out the stove enough to check the board, which was fried. I replaced the board and then looked for the reason it smoked and found that the blower motor was shorted (and stank horribly).
It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent.
The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet.
Everthing works like a charm now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Socket set, Wrench set

CustomerMICHAEL from LAKE GROVE NY

Downdraft motor bearings shot

I FIRST HAD TO PURCHASE THE REPLACEMENT MOTOR WHICH WAS QUOTED FROM A HIGH OF $236 TO A LOW AT GRAINGERS OF$100.00. tHE COUNTERMAN AT GRAINGERS REMOVED THE BLOWER FAN FROM THE MOTOR FOR ME WITH A SPECIAL LONG HANDLED ALLEN KEY. i THEN DEGREASED AND CLEANED THE BLOWER FAN. i HAD TO CUT OFF THE SCREWS ON THE MOTOR AND REPLACE THE 3 MOTOR ISOLATORS AND THE URETHANE FOAM AROUND THE MOTOR. I HAD TO THREAD THE 3 WIRES FROM THE NEW MOTOR THROUGH THE BX CABLE FROM THE OLD MOTOR AND REATTACH THE FAN TO THE MOTOR. ANYONE WANTING MORE DETAILED INFORMATIOIN MAY CONTACT ME AT:mablume@optonline.net

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5