Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11744318
This part has a male spade and helps your burner ignite and produce flame. If a wire lead is needed, you can purchase locally.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Remove screws holding burner down, invert and remove screw in igniter. Reverse to reinstall.
Help other customers find the most helpful instructions.
Were these instructions helpful?
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and then rethreading the screw hole. On to the ignitor replacement. The tiny screw holding the ignitor was corroded and would not come out. It too had to be drllled out and rethreaded. It was a 1/3" #4 screw with fine threads. Had to get it an appliance repair store as the local hardware places don't carry fine threaded screws. Finally got it all put back together after a week. My advice before ordering an ignitor is make sure you can take the current burner off the cooktop first to do the repair in the first place. BTW, the ignitor I ordered came quickly and was the correct part!
Firts I removed the 2 screws that held the burber in place. Then I lifted the burner up & disconnected the wire that connected to the ignitor. Then I removed the one screw that held the ignitor to the burner. I then reversed these steps, replacing the cracked ignitor with the new one, replaced the screw holding it to the burner, then reconnected wire, returned the burner to the stove and replaced the two screws that held it. All Done!
- Removed the cover.- Removed te two Torx screws.- Pulled the burner a couple of inches to be able to disconnect the wire.- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.- Treated all screws with a high temperature copper paste to prevent oxidation.Installed the new ignitor with the new screw.- Reconnected the wire.- Installed the two Torx screws.- Voila, it works.
Removed grate and burner cover (held on by gravity - no tools needed) then removed the two screws holding down the burner itself. These screws are Torx screws so you will need a Torx bit set (looks like a phillips head screw driver but is star shaped). Once these screws are out, the burner lifts off to reveal two phillips head screws holding the ignitor in place. Remove these two screws, un-plug the ignitor, plug in the new ignitor and replace the two screws holding the ignitor in place. Be sure to have the ignitor centered. The first time I put the new ignitor in place, it was touching the frame of the stove, so it failed to spark since it was grounded. Replace the burner and two torx screws and replace the burner cover and grate. Done and done.
Well, after I finally got the parts, the repair was easier than anticipated. You deffinitely want to lift the unit out to replace the spark module and swap over one wire at a time so you dont forget where they go, (important on a gas stove) When I pulled out the old unit I found it was just jammed in there when constructed, I expected more from Jenn-air, and the plastic casing was broke and pulled apart. Surprised it lasted this long. Also three of the ceramic insulators on the ignitors were broke or cracked. But over all the unit was fairly simple to repair if you take your time and practice safety. Remember, you are working with gas and electicity, and use soapy water to check your connection when you reconnect the gas line. Dont try to work on it still hooked up and in its mount . Disconnect it and lift it out.
I removed the burner cap and then the two screws that held the burner in place, pulled it out about 3 inches, disconected the ignitor and pluged the new one in, put the burner back in place and put the two screws back in, replaced the burner cap and it was done. I would also like to mention that I ordered my replacement part on Sunday evening and recieved it on Tuesday morning. Thanks Part Select!!!
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches to disconnect the electric wire - it had a small bayonet connection. I turned the element over and unscrewed the small screw holding the ignitor to the element freeing the ignitor from the element. After receiving the part from Part Select, I reversed the process... 1. attaching the ignitor to the underside of the element using the small screw.2. reattaching the electric wire to the ignitor. 3. positioning the element on the stove top. 4. reattaching the eelement using the 2 screws.5. testing and finding it worked fine.A couple of observations:1. The screws holding the element to the stove are star screws while the screw attaching the ignitor to the element is Phillips - necessitating 2 different screwdrives for an easy repair.2. I had problems with the initial part delivery - it went to a wrong address. PartSelect Customer Service was great. I had a less than 5min wait for getting a rep on the line with the 1 call I had to make to get this corrected. And when I did get a rep she was both helpful, friendly and knowledgeable in correcting the situation.
The ceramic on the electrode broke due to water over boiling the week of Thanksgiving. When i tried to loosen the screw to replace the electrode it broke off inside the threads. Ordered whole new unit overnight. Back in business in five minutes. Thanksgiving was back on!! Thanks!
First reviewed other review on this repair. Disconnected ignitor system from electrical source (pulled plug); removed 2 screws holding casing in place; removed it from the cooktop; & removed additional screw holding ignitor. Replaced ignitor and reversed the process. Done.
Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!
First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.
Should have read the partselect instructions first 1.) unplugged range 2.) unscrewed (torque screws - good thing I had some) burners - one screw was corroded into the top and snapped - will require a drill to remove and replace metal screw. 3) slid electrical wire from contact 4.) unscrewed (with phillips) Burner Electrode assembly (also corroded - took some force) replaced electrode assy and reversed steps. Works perfect.
removed two screws, lifted the element, disconnected wire, removed one screw that holds electrode, replaced anf assembled
Simply removed the old ignitor and install the exact replacement part. Work great.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.