HSS25GFPEWW Hotpoint Refrigerator - Instructions

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

The video instructions were easy to follow as well as the replacement. The replacement Main Control Board is generic to different refrigerators and has more connectors than the original. Be sure to identify the locations prior to removal and installation.

I pulled cover off back that housed the board. Unplugged all the wires that went to the board. wires will only fit in one spot so you cannot mess it up. snapped it off the pegs, then replaced new board in same spot. hooked plugs back up and installed ground wire. covered it back up plugged it in and it ran.

Replacing the motherboard was really easy. However it has not fixed my refrigerator. I continue to have cooling issues with fridge and sometimes with the freezer.

Part received in two days,installed in 5 minutes.Thank you.

I'm a housewife in her late 40's. Before ordering the part, I watched your video on how to remove and install the new icemaker. First I unplugged the refrigerator. After a few minutes, I unplugged the icemaker and unscrewed it. I lifted it a bit and removed it. I did not use the icecup that comes with the part. Instead I removed the one from the old part and inserted it to the new one. Then I plugged in the new icemaker, placed it inside so as to match the holes and screwed it in. YES, it was that simple. It took me less than 10 minutes to do this. I saved myself over $100!!

Just like the video show on the wed site.

Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.

Watched the video from your site and followed instructions, extremely easy after that.

After pulling fridge out from the wall, removing the bottom back panel and inspecting the fridge operating parts, I noticed the condenser fan never comes on. Reading online I found that most of the time the problem is with the main control board. I simply unscrewed the back panel, carefully disconnected the cables from the old board, plugged them back in to the new board, replaced the panel and started the Fridge back up. It cooled right down to normal temperature within the hour! Five years of neurotic behavior around cooling the fridge were over! My wife and I constantly rearranged various fans around the kitchen and joining rooms, opened the cabinet above, taking out the bottom shelf to make more ventilation, pulling the fridge out from the wall several inches, and worrying every time the freezer went up to 9 or 10 or even 20 degrees, and the fridge section up to 40 or even 45 degrees F. I can sleep easy now, and use the fans on us in hot weather, rather than the constant buzz in the kitchen. We can even have a conversation without yelling above the din of the fans!

Took old part out, put new part in. Thats not the story here, it was the ease of finding the part needed, the price was very reasonable and the service was second to none! The part arrived in less than 48hrs. (no special shipping was used) I would like to thank the people at PartSelect for a great experience. Other companies I have delt with in the past could take a few lessons in customer service from PartSelect. I highly recommend them! Patrick Spinks

Watching the outstanding, detailed video provided the insight and confidence necessary to place the part order and complete the repair. The most difficult part of the procedure was removal of the front panel that identifies the buttons for various functions (i.e. water, ice, crushed ice, etc). Note that this panel differs slightly from one model to another so the process may be slightly more difficult than pictured in the video. Our refrigerator has removable decorator panels which I removed first (both above and below the dispenser section), an additional step I strongly recommend for owners of models with such panels. To do so, a male Torx socket is required to remove screws at the top of the door, allowing the metal side panel on the left to be removed, prior to sliding the decorator panels out. Now onto removing the front panel as in the video - although the video repairman completed this step without any tools, it must be CAREFULLY pried by hand. Experience has taught me that older plastic parts that "snap in" often become fatigued and suffer stress fractures if not breaking off entirely. This is a fairly rigid piece of plastic on our unit that wasn't cooperative until I coaxed it from one (left) side with a large, flat screwdriver and a little twisting motion to get things started. Once I was able to pop one corner loose, the other 7 connecting tabs were relatively easy to remove (there are 8 total - 2 on each side as I recall). The rest of the process was simple, exactly as demonstrated in the video. Thanks SO MUCH for all of the expertise and high production values that made this repair "a piece of cake". Incidentally, by simply removing the old solenoid ASAP, the door snaps shut, sealing off the freezer compartment while you wait for your new part to arrive.

I followed the video instructions

after ordering part I went to partselect and watched video. Than I removed old valve and replaced it in the reverse order. it only took 15 min. to do the job.I highly recommend the use of partselect for repairs.

very well, replaced min board in less than half hr.