Models > HDA3400G02WW > Instructions

HDA3400G02WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400G02WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400G02WW
1-15 of 685
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken upper rack roller, rack kept falling off the track

  • Customer: Doug from Columbus OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 367 of 370 people found this instruction helpful
Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.

Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.

Rollers fell off lower rack of dishwasher.

  • Customer: Lloyd from The Villages FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 362 of 363 people found this instruction helpful
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.

The stud assembly in the middle of each wheel no longer stayed inside the wheel.

  • Customer: Wendy Baldwin from Stowe PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 361 of 365 people found this instruction helpful
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.

Rack falling off of upper slides

  • Customer: Eric from Centreville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 186 of 254 people found this instruction helpful
1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away

wheel replacement

  • Customer: michael from perry hall MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 215 of 403 people found this instruction helpful
Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs

Dishwasher wouldn't fully drain

  • Customer: Dan from Minnetonka MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 98 of 108 people found this instruction helpful
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.

Water leak from gate (diverter) valve shaft

  • Customer: Joseph from Livermore CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 78 of 85 people found this instruction helpful
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect.

wheels were worn out and kept falling off

  • Customer: JOHN from PURCELLVILLE VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 65 of 67 people found this instruction helpful
popped old wheel off popped new one on
for the rack roller i took the ends off and slid old rollers off then slid new ones on.

roller on upper rack broken - lower rack plate holders broken

  • Customer: charles from canton MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 88 of 157 people found this instruction helpful
lower rack took one min. take out old slide in new

upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.

front twoo rack rollers broken ,bottom rack roller broken

  • Customer: Russell from Pueblo CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 74 of 136 people found this instruction helpful
for the top rollers you must remove thethe end cap. this was easy ,i placed a block of wood on the outside .placed the punch on the inside where the channel is pushed in to hold cap on. smacked it till it was pushed out far enough to remove end cap. new rollers simply snap on. very easy,

lower dishrack rusted

  • Customer: michael from Bloomington IN
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 41 of 45 people found this instruction helpful
replaced rack, no repairs required

Dishwasher leaking at rubber connector - pump wash arm

  • Customer: Skott from Mason OH
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 70 of 132 people found this instruction helpful
First removed dishwaser from under counter so I could get to rubber connecter. It is located in center under dishwasher. I first needed to unscrew with wrench rubber connection at pump and and then the complete piece unscewed by hand from pump wash arm. I then just had to screw new rubber connector back on to bottom of dishwasher and re-attached at the pump. It was very easy to replace the rubber connector. I also replaced the dishwasher sump housing because it was made of same rubbber material and feared it was deteriorating also. I had to unscrew with wrench at pump as well and it just popped out from inside dishwasher after unscrewing screen inside dishwaser. Popped new piece in and screwed screen back on and reconnected underneath dishwasher back to pump. The rack roller wheel just popped right on. FYI: The wheel is actually 1.75 inches in diameter not 2 inches. I was worried it might be too big if it where 2 inches but it was the same size as the other wheels which was 1.75 inches. The hardest part of this job was getting the dishwasher in and out from under the counter. The good news is that most of these parts are standard and the replacement parts fit perfect.

Dish washer is not running through cycles

  • Customer: mike from huntley IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 41 of 51 people found this instruction helpful
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...

Rollers broke off from bottom rack of dishwasher

  • Customer: Reginald from Hamilton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 65 of 127 people found this instruction helpful
Went to www.PartSelect.com. Part was easy to locate online with GE model number and illustraion online. They shipped the parts in two days and I put the new parts on by hand. Saved a $135 service call from GE. One part came in broken from the factory. Upon calling customer servce, PartSelect sent out a replacement part the next day - no problem. Great service, would be happy to use again - Thank you!

LOST A WHEEL FOR DISHWASHER

  • Customer: LINDA from OCALA FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 63 of 124 people found this instruction helpful
REPAIR EASY..SNAP IT IN......IMPRESSED WITH THE SPEEDY DELIVERY. THANKS
All Instructions for the HDA3400G02WW
1-15 of 685