Models > HDA3400G02WW > Instructions

HDA3400G02WW Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400G02WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400G02WW
46-60 of 685
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Parts were old and worn out

  • Customer: Dave from Littleton CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 13 people found this instruction helpful
The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick.

Dishwasher would not drain.

  • Customer: Jonathan from Athens GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
I removed the four screws of the filter frame exposing the check valve (piston and nut assembly) . I unscrewed the old check valve and replaced it with the new one.

Old Motor Seized

  • Customer: Gordon from Ogdensburg NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 11 of 14 people found this instruction helpful
Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

Replace valve

  • Customer: James from Hartsel CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench set, Wrench(Adjustable)
  • 10 of 11 people found this instruction helpful
Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.

plastic hinge arm link broke causing door to flop open

  • Customer: Margaret from Meridian MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Motor seized on 1990 GE dishwasher

  • Customer: DAVID from UNION MILLS NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 9 people found this instruction helpful
The motor seized up on my 1990 GE Dishwasher
Repair would cost 360. Replacement about 600
I ordered the motor and pump from PartSelect for 137..44
Remover the under counter washer (it‘s very light) and removed the water and drain line and disconnected the power. Turned the washer on it’s top to access the motor and pump and removed the electrical plug in lines, and the clamps holding the pump on to the connections. Replaced it with the new motor and pump, reconnected the electrical plug ins, added an adapter hose part, tightened the original clamps then reconnected the water, drain and electrical connections and reinstalled the washer. All in about an hour, The only glitch was the grounding screw for the ground wire on the motor. The screw was too long to tighten. Substituted the original shorter ground screw from the old motor, and that worked fine. Only used 4 parts from the large assortment of parts supplied.
Immediately ran the washer through a cycle, all worked perfectly.

Dishes were coming out with nasty film and chunks - gross!

  • Customer: Russell from Portage MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 10 people found this instruction helpful
Read about somebody else with the same problem and ordered the check valve. 4 screws off, twist out old valve, twist in new valve, 4 screws back in. Now dishes are see-yourself clean.

accumulation of dirt in behind screen in back of washer

  • Customer: William from Belmar NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 10 of 13 people found this instruction helpful
Pulled dishwasher out. Unscrewed 4 screws holding body valve, disconnected 2 hoses and replaced valve, put machine back together in reverse order.

tub corner baffles were falling apart

  • Customer: ROBERT from GLOBE AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 8 of 8 people found this instruction helpful
I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

Dishwasher was leaking between the pump motor and pump assembly

  • Customer: Jesse from Royal Oak MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 8 people found this instruction helpful
The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

Dishwasher rack was rusting and partially broken

  • Customer: John C from Indianapolis IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
The repair only required me to lift out the old unit and set the new rack into the dishwasher. I was pleased that there was nothing to put together. The rollers were already attached.
It took longer to open the shipping box than to do the installation.

Motor/Pump assembly leaking

  • Customer: Thomas from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 8 people found this instruction helpful
I made this replacement more dificult because I removed the old motor/pump earlier. Should have done it at the time I installed the new unit to be sure all hoses where installed correctly. I hooked the drain hose to the wrong port and when I started the dishwasher I found my error. Once I corrected the problem and started it again - the wash and drain cycles were perfect and there were no leaks.

Water leak at drain valve shaft

  • Customer: Randolph from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 9 of 11 people found this instruction helpful
Before ordering the parts I read the posts by other do it yourselfers and found them very helpful. I ordered the seal and shaft nut from Parts Select and was impressed the parts were delivered in a couple of days. I removed the two lower panels from the dishwasher to expose the leak and the shaft. I turned off the electricity at the circuit breaker box and disconnected the wiring harness to expose the area I would work on. After cleaning the water deposits from the shaft I pried off the small lock washer and removed the plastic cam from the selenoid. Next step required removal of the push on nut. This was the most difficult part of the entire procedure. It required a bit of gentle but firm pulling with pliers and a couple of screwdrivers, sacrificing the nut in the process. It was better ordering a new one originally then trying to save the old one. Having experiencing these nuts in previous work, I knew a new nut would be a cheap fix! Once off, the old seal is easy to remove. Place the new seal on the shaft as per the included instructions, place the new push on nut and reassemble as originally taken apart. (I used a socket set to push on the push on nut.) I then ran a load of dishes to make sure there was no leak before reinstalling the lower panels. I had no leak but pay close attention to placing the seal and push on nut. The seal must be in the exact place.

Dishwasher would not Drain

  • Customer: Alfred from Fernandina Beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 9 people found this instruction helpful
Since the pump and the motor was a single unit, I removed the assembly by disconnecting the electrical plugs and drainage connections. This was a very simple installation. I reversed the above steps, reinstalled the dishwasher and all worked out well.

leaking selenoid told repair cost would exceed replacement cost

  • Customer: Susan from Pottsville PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 9 of 12 people found this instruction helpful
Shut off circuit breaker to dishwasher and shut off valve to dishwasher under sink.Remove bottom access panel screws on both sides of panel. Remove both screws holding dishwasher to counter.Place old mattboard strips under legs to prevent scratching floor & slide out from under counter. Use a Shopvac to remove water and spillage. Have rags and paper towels handy. Carefully disconnect wires, drain hose and water line to free dishwasher. Fold old rug runner in half to place dishwasher on, turn on side and then gently upside down on rug to access motor. Remove butterfly clamps, hose clamps, electrical connections, and support bracket. remove old motor and pump and place in box to discard. Position replacement motor and pump according to diagrams. Reconnect all clips, hoses and connections. Since replacement motor and pump is smaller, use longer support bracket from adapter kit. Return dishwasher to upright position and reconnect wiring using wirenuts, drain hose and waterline. Reposition mattboard strips under legs and slide back into place. Attach screws to counter top. Turn on power, water and do a test run to check for leakage. Replace bottom access panel. Pat yourself on the back since you've saved yourself hundreds of dollars for a repair or replacement of your dishwasher.
All Instructions for the HDA3400G02WW
46-60 of 685