All Installation Instructions for Hotpoint Dishwasher HDA3400F00WW

front lower wheel broke

Insert the piece into wheel and snap on lower rack of dishwasher. Thank you to parts select for such fabulous service and quick delivery and fair price.

Parts Used:

Lower Front Dishrack Wheel

Elizabeth from Deer Park, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

missing top wire basket rollers

Had just a little trouble getting the end caps of the the runner bars after that it was a breeze, I am a 55 year old woman and done the job by myself

Parts Used:

Upper Roller and Axle - Kit of 4

Jeanie from Clinton, AR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Thank you for voting!

upper rack kept falling - upper rollers no longer attached

I watched the video before ordering to ensure I had the right parts. I simply followed the video. So easy! And for less than $20, the dishwasher is repaired. The upper rack was such a hassle, I was considering getting rid of the dishwasher! So glad I found your site.

Parts Used:

Upper Roller and Axle - Kit of 4

Julie from Cicero, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dishwasher would not drain completly

Remove filter screen at rear bottom of dishwasher with 1/4 in socket, remove check valve by hand, install new check valve, reinstall filter screen. Run a load of dishes, drained completly.

Parts Used:

Piston and Nut Assembly

Paul from Avondale, AZ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

serious rust & corrosion on the rack

just lifted out the old one & replaced it with the new one. Couldn't have been easier.

Parts Used:

LOWER RACK

Elizabeth from Ames, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Water Inlet Filter

Before you due anything else...remove the water inlet valve, remove the 4 screws holding the water inlet coupling to the valve housing, remove the nylon filter (tight fit), and clean the debris from the filter. Re insert the filter, reassemble the valve housing and check for leaks. Clears most water flow problems.

Parts Used:

Water Inlet Valve

Steve from Cibolo, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

Thank you for voting!

End cap broke

Ordered the part from you and it was easy to replace.

Parts Used:

RACK SLIDE END CAP

James from Las Cruces, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

replace pump motor assembly

Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.

Parts Used:

Motor and Pump Kit

Ben from Nashville, TN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

See below

In replacing the upper rack in our dishwasher, I struggled and broke one of the end caps (see previous tale of woe. With the new end caps, I finished the job in less than two minutes with no tools. BUY END CAPS when you order a rack!

Parts Used:

RACK SLIDE END CAP

Leslie from Amarillo, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

The smallest portion of the sprayer had been broken

Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!

Parts Used: