HDA1100Z06WH Hotpoint Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not drain.
The dishwasher was in a rental so I didn't want to spend the money for a new one. The part was expensive compared to a new (cheap) dishwasher. The order was shipped promptly and arrived when I expected even though it was Christmas time. The part fit perfectly and everything is back in place.
Parts Used:
-
Thomas from VICTORVILLE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
new bottom dishwasher rack
-
Jose from Anthem, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water during wash cycle.
Shut off water, disconnect power,remove
Faulty valve,install replacement part.
Faulty valve,install replacement part.
Parts Used:
-
Jason from Porterfield, WI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaky dishwasher
remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.
Parts Used:
-
kenneth from ocean isle beach, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken off end caps, top would slide off, frustrating.
did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.
Parts Used:
-
Paul from Blairs, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leak
I shut off water and pulled dish washer out removed all water. Turned waasher upside down.
Removed sump housing screws and unscrewed
pc fitting ,replaced new parts. Make sure things are tight before turning on water.
Removed sump housing screws and unscrewed
pc fitting ,replaced new parts. Make sure things are tight before turning on water.
Parts Used:
-
Georgina from Poplar Grove, IL
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench set
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part of a roller on the upper rack had broken
I removed screws holding the rollers to the side of the dishwasher. I pried the end caps from the slide. I removed the broken part from the upper rack. I then replaced the broken rack roller, inserted into the slide and screwed the rollers which hold the slide into the sides of the dishwasher.
Parts Used:
-
Janice from Murphysboro, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing wheels on lower dish rack
Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.
I was very happy with the fast delivery by PartSelect.
I was very happy with the fast delivery by PartSelect.
Parts Used:
-
Shoji from Arlington, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drain solenoid burned up
Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.
Parts Used:
-
David from King Of Prussia, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower dish rack was missing one of the front wheel.s
Super-easy and quick repair -- quality part snapped right into place.
Parts Used:
-
Jason from Redmond, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher did'nt drain water . solinoid was melted and stuck
First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.
Parts Used:
-
Ben from florida, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace rollers on dishwasher rack
The hardest part is removing the plastic stop on the end of the two slides that support the roller rack. My unit was very old and I was afraid the plastic was brittle. Fortunately, the plastic could still be bent without breaking. You need to physically bend the plastic stops to remove. They came out easily, but you do need to apply some force.
Replacing the rollers was simple. Replacing the stops was easy once you understand how to pry them out. I would recommend trying to remove the stops with your hand only at first. You are less likely to damage the plastic.
Replacing the rollers was simple. Replacing the stops was easy once you understand how to pry them out. I would recommend trying to remove the stops with your hand only at first. You are less likely to damage the plastic.
Parts Used:
-
Clifford from Sugar Land, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rack rusting
Took end caps off roller guides. Slid old out...slid new in...poped end caps back on...done. Too EASY!
Parts Used:
-
melissa from ferrum, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The sprayer that pops up during the wash cycle broke
I popped the old one off and snapped the new one in. It was pretty simple and it works perfectly!
Parts Used:
-
Rachel from Pacific, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
6 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper rack fell into lower rack breaking dishes
My GE dishwasher had a problem. The upper rack would fall into the lower rack when loaded breaking dishes! Turns out, the front rollers on the upper rack were broken so that the supports would just pull out. So, I found the parts on this website easily. I then took off the plastic plug on the support which is easy to do. There is a flange you bend towards the rear of the dishwasher to release the plug. Once released you have access to the rollers, which just snap off easily. The new ones snap on easily. Reverse the cap removal, and you are done!
Parts Used:
-
Daniel from Sebastopol, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!