GW397LXUB0 Whirlpool Range - Instructions

I installed the Cap-Burner on the left front right, and then the gas ignited and I was able to use the stove.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

Removed oven door, removed bottom of oven, removed old igniter, installed the new one and plugged it in in the back of the stove. Installed oven door and it works fine. .

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

Watch the video. Spot on instructions. Easy peasy.

1. Open oven door to first detent, then pull it up off the hinges.
2. Pull oven out from counter 10-12 inches.
3. Hinges are accessible from the outside of the oven.
4. Remove 2 screws on each hinge and remove old hinges.
5. Put new hinges in place and try to insert mounting screws.
6. Wonder why screws won't start in threads.
7. Examine new hinges and notice they are not threaded for the screws.
8. Screws are not self-tapping, so go to basement and get tap & die set.
9. Use 10-24 tap to make threads in new hinges.
10. Put new hinges in place and insert mounting screws. Tighten.
11. Pull hinges to first detent and put oven door on hinges.
12. Push oven back into place in counter.

First I changed the temperature sensor and when it didn’t get hot I Also changed the igniter. Fired right up.

Watched first warranty repair tech preform first costly replacement by removing 8 panel screws on face of oven. Same malfunction twice in last 4 years. The second and third replacement I did myself with just my trusty screw driver. Tip: Keep order receipt handy for easy reorders.

I took the door off and removed five phillip screws from the old bottom support and removed it. I took the opportunity to clean the glass on the front and back before placing it back on. It simply fits into two keepers at top and is held on by the new support at the bottom. I replaced the five screws and put the door back on. It is a simple job that only takes a few minutes.