GSG25MIMBFBB General Electric Refrigerator - Instructions

Removed the front panel on the door that has the ice maker controls. Removed the screws and parts. Reassembled the parts and it works better than new. Ice door closes firmly and holds tight.

I removed the screws for the inner door and removed inner lining. Then took out the ice dispenser in the door. Took off control panel on the front of the ice panel. Removed the rusted parts and put in new parts. Put all parts back the way it came apart. In retrospect.... I could have possibly replaced the parts from the front panel but by taking apart the door...I had to thaw out the inner panel and insulation with in the door.

First I removed the vegetable drawer and glass shelf. I matched up the 'new' drawer slide rail next to the broken slide.
I then used a phillips head screwdriver to remove the 2 screws that held the slide in place.
After removing the broken slide rail, I installed the new rail, replaced the vegetable drawer and glass shelf. New item worked like a charm.
The drawer slide arrived really quick after my order was placed. Approx. 2 days after ordering the part, it was on my front door step.

I had taken the noise long enough and wanted to get this repaired. I didn't want to pay a repair man hundreds of dollars to do it so i decided to do it myself. I went on to YouTube and found a few videos that showed me how easy it was to do (very helpful).

I wasn't so sure all that noise would come from the Evaporator Fan motor so i ordered it and took the chance. For the small cost, it was worth the try.

All went well accessing the unit and removing the old part. Very fast indeed. However, the snag came when i went to plug in the new part electrical to the existing electrical adapters. The old part had 4 lead connections. The new part had 6. and the wires on the new part were different colors than the existing. I had to use some logic and courage to cut the wires on the new part and rewire the old adapter to this piece. Luckily, i wired everything correctly.

Calling Part Select got me a phone number for the parts manufacturer to help with the splicing but i opted to do it on my own.

The result is i have a noiseless refrigerator again. What should have taken 10 to 15 minutes took half an hour because of the wiring but overall, very easy.

The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

My refrigerator's initial problem was as follows:

1. Freezer fan stopped circulating the cooled air. Causing food to thaw at the top of the freezer, and freeze solid at the bottom. Ice in the icemaker thawed.

2. Water dripped from the freezer door gasket when the freezer was in defrost mode & water dispenser would not dispense water.

--FIX (the easy one first..):
2. I removed the inner freezer door panel and found ice filling every void of the freezer door panel-approx 5 lbs of ice dammed in the panel. I thawed the insulation and removed the ice. Also there is a styrofoam insulating surround around the inside of the dispenser panel. The styrofoam had become saturated with water and was freezing, allowing the drinking water tube to freeze, not allowing the refrigerator to dispense water...
THE CAUSE:
2. Overflowing of water from the in-door ice/water dispenser compartment reservoir (just under the grill where your glass sits, when it's dispensing water) was draining into the freezer door panel.
PREVENTION:
2. Check the reservoir more frequently to make sure water does not build up and overflow into the door.

FIX (now the trickier one..)
1. I initially thought it was the main circuit board. I replaced the board. Access is by removing the 3 hex nut screws holding door in place at the rear of the freezer. Disconnect connectors & using a needle nose pliers, squeezed the plastic catches that hold the board in place. Connect the new board (being careful not to touch the components or traces on the board) to the connectors, then snap into place using the white plastic catches.
Close everything up.

NOTE: This may, may not have contributed to the problem, but my refrigerator light went out. I replaced it with a small flouresent bulb. That bulb did not last, and became inop. Shortly afterward, the freezer started malfunctioning. I replaced the board, and the freezer was still somewhat intermittent. I replaced the bulb with an appliance 60 watt. The freezer has been perfect since...

Note: I first ordered the main circuit board, when that didn't immediately fix the problem, I ordered the above parts. I did not need the parts and am returning them. The web page is forcing me to select at least one of the parts needed for the repair, when I used neither.

After figuring out how to remove the old broken clip, replacement was easy. Had to use a small putty knife to open the release on the bottom underside of the clip(between the clip & the refrig) . By looking at the replacement piece it was easy to figure out.

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.

Shipping service was great> Ordered on a Friday, received it on Tuesday. Slipped out the old one and put the new one in and it works great

Replaced flapper

used a phillips screw driver to remove two screws that held
the crusher assembly on the end of the ice bucket. Then I used the flat blade screw driver to pry the slot locks open and removed the dispenser cover. reassembly was areverse process.

i used the video it showed on the site or iwould not have been able to do it

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

Replaced entire ice bucket and auger assembly (one piece).

I replaced that part, but I still have the same problem, no water is dispensed. I believe I may need a circuit board. The problem was not the parts I replaced.