284986-1-M-GE-WR02X10552-Evaporator-Thermistor-Clip.jpg
284986-1-S-GE-WR02X10552-Evaporator-Thermistor-Clip.jpg 284986-2-S-GE-WR02X10552-Evaporator-Thermistor-Clip.jpg

Evaporator Thermistor Clip

PartSelect Number PS284986

Sold individually.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $2.57
  • You Save

    $.43
  • Your Price

    $2.14
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.4 / 5.0, 3 reviews What's this?
1-3 of 3
 

195 of 226 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerGerald from San Clemente CA

Fridge too warm, evaporator icing up

After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers

CustomerMARCELLA from FAIRDALE KY

Freezer was not cold enough to keep food frozen or make ice

I AM A SINGLE MOM OF TWO WITH LIMITED FUNDS. I HAD A REPAIRMAN COME OUT AND FIND THE PROBLEM AND GIVE AN ESTIMATE. WE WERE TOLD THAT IT WAS THE EVAPORATOR FAN MOTOR AND AND THE MAIN CONTROL BOARD. THE REPAIR WOULD COST $400 AND NO GUARANTEE. SO I CHECKED THE COST OF PARTS AND IT WAS $200 SO FOR NO GUARANTEE I FIGURED WHY NOT TRY IT MYSELF AND POSSIBLY SAVE $200. SO I ORDERED THE PARTS FROM PARTSELECT. EVEN THOUGH I PAID THE CHEAPEST POSTAGE THEY ARRIVED THE NEXT DAY. SO FROM WHAT I READ AND SAW THIS WOULD BE A PIECE OF CAKE. WELL LET ME JUST SAY IF THE FREEZER SECTION WAS GUTTED TO BEGIN WITH IT MIGHT NOT HAVE BEEN THAT BIG OF A DEAL. AS IT WAS GETTING TO THE TOP SCREWS OF THE PANEL THAT COVERS THE EVAPORATOR FAN REQUIRED THE REMOVAL OF THE ICEMAKER AND ALL. I AM NOT A TALL WOMAN NOR AM I A THIN WOMAN AND FITTING MY BODY IN THAT SMALL FREEZER SECTION WAS NOT EASY. THERE WERE TIMES THAT I HAD TO HAVE MY TEENAGERS REACH A LONG ARM IN AND HOLD A PART UP FOR ME. AFTER THAT I DISCOVERED THAT THE FAN I HAD PURCHASED ONLY HAD 4 WIRES. THE ONE FROM MY OLD FAN HAD 6. I DISCOVERED THAT 2 OF THE WIRES WENT TO SOME SORT OF SENSOR. LONG STORY SHORT I RIGGED IT. I WAS ABLE TO REMOVE THE 2 PRONGS FOR THE SENSOR AND INSERT THEM INTO THE EMPTY HOLES ON THE NEW FAN HARNESS. IT WASNT EASY. I HAVE LIMITED TOOLS TOO AND I WONT EVEN GET INTO HOW I DID IT. THEY DID NOT FIT THE GREATEST SO I USED THE ELECTRICAL TAPE TO COVER THE WHOLE CONNECTION. I PUT THE WHOLE THING BACK TOGETHER AND DEBATED ON TRYING IT WITHOUT PUTTING IN THE MAIN BOARD BUT I DECIDED TO TRUST THE REPAIRMAN THIS TIME AND GO FOR IT. GETTING TO THE MAIN BOARD WAS NO BIG DEAL. BUT WHAT DISTURBED ME WAS THE MAIN BOARD I HELD IN MY HANDS DID NOT LOOK EXACTLY LIKE THE MAIN BOARD I WAS ABOUT TO TAKE OUT. I WATCHED THE VIDEO 3 TIMES MY HOW EASY IT LOOKED. I THEN READ THE DIRECTIONS THAT CAME WITH IT. IT TALKED ABOUT REMOVING A PIN AND CUTTING A WIRE. WELL I ABOUT HAD A STROKE WORRYING. I FINALLY FOUND THE SERIAL # ON MY FRIG AND THANKFULLY MINE WAS NOT ON THE LIST. HOWEVER THE DIRECTIONS DID STILL SAY SOMETHING ABOUT IF THERE WASNT A WIRE IN PIN 2 PROCEED TO STEP 3. WELL I HAD A WIRE IN PIN 2. SO IT WAS CONFUSING. MY SERIAL # WASNT ONE OF THE MODELS #'S GIVEN BUT I DID HAVE A WIRE IN PIN 2. I JUST TOOK A CHANCE AND TRUSTED THE SERIAL #'S AND IGNORED THE REST OF IT. I PLUGGED THE WIRES ON THE NEW BOARD ONE AT A TIME. PUT THE COVER BACK ON AND PRAYED AS I PLUGGED IT IN. A SOFT PURR BEGAN. IT WAS RUNNING. THE FREEZER WAS AROUND 60 DEGREES. I PUT A ROOM THERMOMETER IN TO MAKE SURE IT WAS GOING DOWN. IT KEPT GOING DOWN. AROUND 3 HOURS AFTER I FINISHED THERE WAS A LOUD NOISE FROM THE FREEZER. IT HAD MADE ICE SOMETHING IT HAD NOT DONE IN MONTHS. I STAYED AWAKE MOST OF THE NIGHT WATCHING AND LISTENING TO IT. IT GOT DOWN IN THE SINGLE DIGITS I WAS AFRAID THAT MAYBE IT WOULD NEVER SHUT OFF. IT FINALLY SHUT OFF AS I WAS MAKING THE KIDS BREAKFAST THE NEXT MORNING. OF COURSE I WAS WORRIED THAT IT WOULD NOT RESTART. SO I OPENED THE FREEZER AND FANNED IN ROOM AIR. IT WORKED. SINCE THEN WE HAVE PURCHASED NO MORE DRY ICE OR REGULAR ICE. WE BOUGHT A TUB OF ICE CREAM AND MORE THAN ONE DAY OF SCHOOL LUNCH STUFF AT A TIME. BOTTOM LINE IT WORKS. THANKS TO EVERYONES POST AND TO PARTSELECT FOR THE VIDEO. I HOPE THAT I NEVER HAVE TO DO IT AGAIN THOUGH.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • Evaporator Thermistor Clip

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver

Customerroy from spring hill KS

Going from warm to to cold

i used the video it showed on the site or iwould not have been able to do it

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3