Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken freezer light switch
Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.
My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.
as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.
The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!
i removed srews from area until i could access the fan unit and removed it. wires were not identical so i had to splice some together, most likely could not have been avoided. the exploded parts diagram helped me to be sure that i would have all replacement parts on hand so i wouldn't have to wait for something i had forgotten.
Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!
Pretty much self explanatory.Removed drawer and anything on top of glass shelf.Remove two screws holding on slide.Replace with new slide.Repeat on other side.Replace shelf and drawer.
I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor Peter
The front wheel pivot pin walked out causing the front wheel assembly (mobility front assembly) to collapse into the refrigerator base
A second person is necessary to help prop up the refrigerator. One person will need to insert a 6 inch support under the front of the refrigerator base while another person rocks the refrigerator back to provide access for the support to be inserted.
The front refrigerator panel was removed to reveal the refrigerator base and provide access to the front wheel assembly adjustment screw (screw mobility). The front of the refrigerator was propped up on a solid support about 6 inches above the floor to provide access to the front wheel assembly and allow removal through the base of the refrigerator. The front wheel assembly was dislodged from the base by first removing the pivot pin by hand and then prying the wheel assembly loose with a screwdriver. Normally the pivot pin would need to be released by prying it loose with a screwdriver and then pulling to free by hand. Once the front wheel assembly was dislodged the adjustment screw was removed with a socket set and the front wheel assembly fell out of the refrigerator base. The new front wheel assembly was then inserted into the refrigerator base, the new pivot pin was inserted and aligned with the support holes and pressed into place to secure with locking mechanism. The new adjustment screw was then inserted into the refrigerator base hole, aligned with the front wheel assembly and hand tightened to set the first threads. The adjustment screw was then tightened with a socket set to seat the adjustment screw. The refrigerator was then lowered and the adjustment screw was adjusted to level the refrigerator. The refrigerator was then pushed back into its normal position and a final adjustment performed to assure the refrigerator was level. The front refrigerator panel was then pressed back into place.
repair was simple removed glass shelf and removed the two screws holding rail in place. I was really amazed at the quick service that I had receiced, I ordered two of the same part and they had the instructions to send back the additional part in my email the next day. Thanks for your help.