GC2225GEK3 Maytag Refrigerator - Instructions

The parts discription was a bit vague and I wasn't sure exactly what I was ordering, but I received everything I needed and it works fine. The combination screw conveyor/ice crusher came in one piece. The ice cube bin is a plastic assembly that snaps apart. I used a wide blade screw driver carefully to facilitate assembly/disassembly. Once you have it apart the old converyor slips out and the new one slides in. Do not remove the two screws that hold the new assembly together. You need a phillips scredriver to take out two of the screws from the old assembly and put in the new one. That is, there are four screws and you need to trasfer two of them. Everything now works fine.

Pull out old module...
Remove 2 wires...
Tape to inside wall [don't want them to fall down into side panel]..

Order new switch..

Fed Ex pkg came on 2nd day..

Install wires on switch...
Press into opening...
Check door light on..[OK]
.. Done

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.

remove top plastic cover / phillips screw driver
remove top door bracket / 5/15" socket
lift off door
remove pieces of old cam / phillips screw driver
replace cam/ phillips screw driver
replace door
replace top bracket / 5/16" socket
check alignment

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Turned old one until it snapped out. Replaced it with a turn.

This is a side-by-side refrigerator. The crushed ice wheel is part of the icemaker bin auger, and it began to fragment, popping pieces of plastic into the ice dispenser and on into our drinks. The manuf. manual had nothing about parts in it, so GREAT thanks to Partselect for their website!!! Now, to dismantle the bin and auger is simple on this design: remove the bin from the freezer and allow it to defrost and dry; there are two small phillips-head screws on the front underside of the bin, holding the front panel in place - remove these screws and pop the front cover off; you'll then see two small phillips-head screws holding the auger-cap in place - remove these and pull the auger cap out, along with the auger; using a small pliers, remove the nut from the auger at the auger-cap, then slide the auger-cap off; at this point you just start removing washers, blades, etc, from the auger - MAKING SURE YOU KEEP THEM IN ORDER - until you reach the crushed ice wheel; separate the wheel from its metal brace, slide the wheel off and replace it; gradually replace all the other parts in order, cleaning them as you go, and simply put everything back together. It helps to keep the exploded parts diagram at hand - available on the Partselect website. It was a snap. The ordering process was simply and the part was delivered to my door on the second day after ordering.

Remove the light cover. Use a flat head screw driver to push in the tabs on the back of the program mount and pull down to expose the computer board. The Thermistor is clipped on under the vent holes on the right side. Cut both wires to remove the old thermistor strip a 1/4 inch off the remaning wires and the new thermistor wires twist both ends together crimp on the wire caps snap in the new thermistor reinstall the program board until the retainer clips snap into place, slide the light cover back on.

I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.

With the repair parts ordered and received from PartsSelect.com, I was able to install a new Ice Bucket and the crushed ice agitator assembly. This simple repair has the refrigerator dispencing ice like new.

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

Turned the old one to unseat and replaced with a new one in the reverse order.

It was great. We replaced the thermistor A little difficult to get to the thermistor but once we found it five minutes. My refrigerator seems happy but we will monitor it and see.