Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken siphon elbow
I thought it was going to be next to impossible to find a replacement part for an older washer. So my first attempt was to try to epoxy the original part, but the epoxy didn't hold up to the stress. I began thinking about what I might need to make a replacement part which was possible but not very practical. Although I dreaded trying to find this part online, I was very surprised and elated to happen upon PartSelect! Oh, by the way, this washer belongs to my daughter and I nave tossed the paper I wrote the model number on, so the model number was entered as the part number, sorry. At any rate, the the part was reasonable priced, and shipping about standard, but I still saved a lot by doing it myself rather than having a repair person for something this simple. Partselect online lookup made it easy to find the model and drawings to help me find the correct part nomenclature. AND, the part was in stock! So I am pleased with how this venture worked out.
Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck
lid closing to far bumpers missing and fuse block cracked
unhooked power plug removed 2 top screws tilted topfront panel back removed cracked fuse holder replaced with new fuse holder put top cover back on installed 2 top screws plugged in power cord done!
Water leak from Water Inlet Valve and tub to pump hose
Water Inlet Valve: Unplugged machine from the AC receptacle!! Disconnected inlet hoses from valve, removed 5/16" screws securing valve to machine rear cover, removed wires from valve, disconnected the fill hose at the valve being careful not to let it fall into the machine, attached the same hose to the new valve along with the wires being careful to make sure they were attached to the right connectors and attached securely, placed the valve into the place where the old one had been and secured it with the aforementioned 5/16" screws, Done!! Hose: Removed front machine cover by removing two screws at the bottom of the machine, removed to clamps, pulled hose from connections, replaced hose with NEW clamps!! Done!
Washing machine lid hinge balls fell off machine lid
First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixed to your machine where you can lift the lid and it will stay up without falling.
Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.
This repair started because I wanted to clean the lint build up out the exhaust vent. But when I moved the washer out, the tile floor was buckled from water damage. So I removed the old tiles and coated the cement with waterproof paint and sealed the seams of the baseboards. Then before reinstalling the washer I had to locate the water leak. I looked at the water inlets and the faucets and saw (and felt) nothing wet. Then I started the wash cycle and looked for the drips. I found them on the left side coming from under the unit. I removed the water inlet plumbing (two screws hold it in place) from the back of the washer but there was no leak. Finally I removed the front panel and could see water running down the side and coming from near the top of the machine. This was right behind the water inlet unit and I thought that one of the hoses was leaking. To get to that area I then removed the top casing and found the injector port was leaking, not the hoses. To remove the front panel I had to take out two screws at the bottom of the panel. To remove the top I had to remove 4 screws...the two rear screws were easily accessible but the two front screws were inside the unit and the one on the left had restricted access because of the electrical unit installed there. After the replacement parts arrived it was relatively easy to remove the front and top again to gain access to the injector port. I removed the old nozzle and valve and installed the new parts. Then I started a wash cycle to check that the leak was fixed. The water did not leak so the repair was successful.
First removed the two lower screws from the front panel. I then unscrewed two screws holding the top(lid) of washing machine. I then lifted the lid and let it rest on its rear hinges. The syphon is removed by unscrewing four screws from the rear of the washer. I then cut the original clamp holding the syphon to the hose. New syphon was installed. Enclosed hose clamp was used to tighten around hose. Syphon was then then screwed back to the rear wall of the machine. Easy fix. Water leak solved.
Tried the water level control first. didn't fix it. Then replaced the air tube for tub fill volume.
The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it. The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so it changed the air volume. That reduced air volume caused the air pressure to be wrong to the water level sensor. My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.
Washer making high pitched squeal at stopping of spin cycles
My washer is apparently 37 years old. I bought it used in the 90’s and have had to do little or nothing to it repair wise. It started to make a loud squeal/squeak when the spin cycle stopped. I watched a couple videos showing the brake assembly, bearings and belt replacement and was able to find parts. However, one bearing appears to no longer be made (just repacked with heavy duty grease) and the special tool is nonexistent. I read others using a chain clamp vise to remove the brake assembly and bought a 20 inch chain clamp vise and a 3 set variety of vise grip pliers for about $20. They make an 18 inch chain vise but glad I got the 20 inch. I used two vise grip pliers to clamp chain around notch two notches that the specialty tool would normally grab. It was a cumbersome getting in there to whack the pliers with a small sledge hammer so I got a approx 18 inch 2x4 and cut a notch at the end to keep chain vise from digging into bottom of washer and whacked the end of the 2x4. Seemed to work ok and did the same to tighten back after replacing break assembly. Got it out back together and no more squeal.
It was as simple as leaning the machine back far enough so I could get to the belts - which were on the bottom. The diagrams that came with the ordered parts were right on. This is the first time I have attempted this myself - my repairman has retired - I'm sure I will do it again.
Tub was filling up with water slowly when washing machine was off
Turn the water supply off. Disconnected the hot and cold hoses from wahing machine. Unplugged the machine from power supply. Removed two screws holding the water inlet valve to the machine frame. Took the old valve out and marked the wire connectors. Removed the wire connectors and the remaining hose from the old valve. Took the new valve and connected the wires paying attention to the markings made earlier. Uses the little adapter hose which came with the new valve to make the new hose connection on the outlet side of the valve. Put everything back and it worked fine. These partselect guys are very prompt in sending the things you order. I have used them many times and am very happy to deal with these guys.
Water leak coming from rear, left side of washing machine.
Removed front access panel--very easy, two screws at bottom of panel, near the floor. Removed two more hex-headed screws that secure the top panel/lid to the top of the washing machine frame. Most difficult problem was identifying the source of the leak. I saw water running out of a white, rectangular (about 1" x 3/4" x 3/4") box-like device that was installed in the water line that leads from the mixing valve (blue box, mounted at the back of washer) to the top of the tub. Discovered this device is called the injector assembly, have not yet been able to figure out what function it serves. Disconnected one of the hose clamps that secure the injector assembly to the water hose. Removed the rubber injector valve and injector nozzle, the two parts that fit inside the above-described "box." Soaked the assembly "box" in vinegar to eliminate hard-water deposits. Replaced the two internal parts (injector nozzle & injector valve) with new (about $15, including shipping). This almost resolved the problem, still saw a small amount of water leaking from the whole assembly, but only about 5% of what was leaking. Haven't yet figured out why it's not completely dry, or what function that injector assembly serves.
Frist remover the two screws from washer front. The ones that are about 5 inches from the floor. Pulled front cover toward me and removed. The hose was right in the front that was cracked. It was held on by two hose clamps. I just removed the old and put in the new. No more water on the floor. Shipping was fast for the hose too. They said that if they recieved the order by 3pm it would be shipped the same day. I order at 3:01pm Sat. recieved Tuesday.