FA4141 Amana Washer - Instructions

First check that the screens are not plugged. There are fine screens in the mixing valve and at times you will find them in either end of the inlet hoses. Not a hard job if you can get to the back of the machine, just a few small screws, swap the wires to the new part and swap the outlet hose from the valve and screw it back together. Wife will think you are a wiz kid.

Studied, diagnosed the issue, looked at symptoms described in ParrtSelect's on line resources, purchased the part. Had it in one day without the need for extra FedEx shipping charges; waspleasantly surprised to see how easy this repair was to make. I then replaced inlet hoses with new stainless steel types. This workhorse pair of of Maytag appliances, constructed in January 1985 will continue to serve for many more years. These are well-built battleships! And PartSelect will be my part source of choice to keep them going!

Repair was pretty simple, as I was able to access the valve from the rear of the washer without having to remove any large panels. All I had to do was disconnect the water supply hoses, and remove a small cover at the rear of the washer (the valve is mounted to this cover). Cleaning the electrical connectors, which were lightly corroded, took longer than anything else. Replacing the valve with the new one was just a matter of making sure the electrical connections, and the hot and cold water supply hoses were attached in the same places as the old installation. There is also a water outlet nipple on the top of the valve which had to be connected to the inlet hose, and I replaced the old clamp with a new one, which I believe is always a good idea. Two screws attach the valve to the cover, and two more screws attach the cover/valve assembly to the washer.

Removed hoses and inlet valve from washer, replaced inlet valve by attaching the electrical connectors, reattached new water lines, returned inlet valve to its place in rear of washer. Checked for leaks, washed a load of clothes, everything worked properly.

My nephew followed directions in the repair video. Washer no longer leaks when warm water is specified.

After watching the video on PartSelect, I ordered the part and received it the next day! The hoses involved were over 24 years old and is the only reason it took longer than about 10 minutes. The hot water hose was dificult to remove. Once I removed the hose, the old water inlet valve was replaced with the new valve within minutes...quick as per the video. The washer is back and was down for less than 1 full day.

Shut off hot and cold water supply and removed hoses from mixing valve. I unplugged the machine and removed the screw holding the plate that the valve is connected to. I removed the plate and valve and used my smart phone camera to photograph the wiring connections. The next step included removing the wires, the hose and clamp. Remove the valve from the plate. Reverse the procedure for installation. Make sure that the valve and plate are adjusted as far from the drum to prevent contact when the machine is going through spin cycles. The procedure took about 10 minutes and fixed the problem. You have to love Maytag for their reliability and ease of maintenance.

Disconnected the electric plug and removed the water hoses from the washer. Took off the old water inlet valve under a plate on the washer and hooked in the new one. As we dismantled each section of the valve hook-up we connected that area of the new valve to be sure we got it connected correctly.

Remove the front panel by removing the screws at the bottom of the panel; remove the screws holding top and swing back on hinges; loosen the screws on the back holding the valve and replace the valve following how the defective one was attached and then reverse the operation.

Just as the video described.... Unplugged the machine, turned off the water, both hot and cold. Unhooked the hoses (replaced them at this time since they were over 5 years old). Took out the top screw holding the frame piece and removed from machine. Took off the wires and the output hose. Removed the valve ass'y from the frame piece. Matched new to the original and reassembled in reverse order.

Ordered replacement water inlet valve, switched out within 10 mins and problem solved for less than $50. Maytag design easily allowed for the inlet valve unit to be replaced without accessing interior workings of the washer. The unit is mounted with 3 screws on a removable rear panel where the hot and cold H2O hoses are connected. Very easy! Tested immediately upon completion and was delighted to see that hot, warm and cold water filled the tub extremely fast, the way it worked when purchased new 18 years ago. The web site repair video was key to my success.

Shut water off and unplugged. Used channel locks to remove hoses. Used nut driver to remove mounting plate. Disconnected electrical connections to solenoids. Broke one. Had to replace. Used nut driver to loosen fill hose. Rusty and broke. Cut hose. Used new clamp to secure fill hose to fill solenoids. Stripped and crimped on new connector and replaced electrical connections as they were removed. Reinstalled hoses and plugged in. Tested A-OK.

The most important part of my repair was watching the video that was sent to me with my order confirmation. After I viewed it, the rest was easy. The only hard part was moving the washer away from the wall!

I ordered the part. Watched the video and did the repair. I removed the cover plate on the washer, removing the screws. I then, removed the broken water inlet valve and replaced it with the new one. I placed the cover plate back onto the rear of the washer and "VOILE", it was done. I am a divorced mother of three, who has never attempted to do any type of home repairs, however, the way PartSelect has set up the website, it made it easy to determine what part I needed and provided me with a video which gave me step by step instructions on how to repair it. I even posted my victory on Facebook! Thanks PartSelect.

Because the washer was old, 27 years, I actually ordered a new machine but after doing so was able to get the old washer to pump out the water. It had overfilled and spilled water on the floor. The next time I ran the washer using "warm" setting the hot water inlet solenoid failure was evident. I checked voltage at the solenoid and it was getting power so figured I'd try ordering a $30 part. In a couple of days it showed up and after less than :30 minutes I had the washer running again. It would have taken less time but a screw stripped out and I had to locate a replacement. I'd definitely recommend PartSelect. Oh, we cancelled the replacement washer and figured the Maytag repairman could resume his slumber!