FA4141 Amana Washer - Instructions

I ordered the water valve at 12:42 PM one day and received the part at 10:25 AM the next morning. Now this is what I call excelent service. The price of the part was very reasonable. Getting my wife off my back for her washer being broken PRICELESS.

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

First let me commend PartSelect for their incredibly fast shipping. Ordered on a Thursday and it arrived on Friday!!

The repair itself was fast and easy and let me add I had never worked on a washing machine before.

1)Unplugged power cord from the wall.
2)Turned off hot and cold water at the shutoff valves.
3)Disconnected water lines leading to the washer.
4)Removed 3 screws holding the bracket assembly on the washer.
5)Removed bracket and pulled water inlet valve out a few inches.
6)Held new inlet valve in same orientation as the old one and then one by one removed the four electrical wires from the old solenoids and attached them to the corresponding place on the new inlet valve.
7)Put inlet valve back in place, attached bracket, and secured it with the 3 screws.
8)Attached water lines to inlet valve and plugged power cord back in.
9)Turned water back on at shutoff valve and checked for leaks.

I washed a load of clothes after the repair and am happy to report that the hot water now runs in as fast as it did when the machine was new. This washer may be 30 years old but I think the old gal's got some life left in her yet.

The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!

First I remove the hot & cold water hoses using an adjustable wrench. I then unscrew the panel that holds the water inlet valve using a nut driver. I then carefully pull out the panel, moving the harness wires out of the way, so that I can loosen the clamp holding the inside rubber tube. I remove the old water inlet valve from the panel by removing the 2 screws and then put the new one in. I then reconnect the rubber tube and tighten the clamp. I then screw back the panel and reconnect the hot & cold water hoses. It took me about 20 mins to complete the job.

Took out 2 5/16" screws and loosened top and took off two ground wires and 2 hot wires for cold & hot water solenoids and removed & replaced solenoid wires and fill hose. Also Had fantastic delivery of parts.

Diagnosed the problem and ordered the part online in about 15 minutes. Part arrived about 3 days later. I followed the directions that came with the part and VOILA! washing amchine fixed. I unplugged the washing machine. I unscrewed the the screws at the back of the machine. Pulled out the faulty part and disconnected the electrical wires. Connected the electrical wires to the new part, and screwed it back in. In less than 30 minutes, I was done.

First, I opened up the back of the machine to see the way the water got into the tub. I turned off the water at the pipes, unplugged the machine, and disconnected the hoses from back. There were no leaks with the hoses, so I looked at the part that managed the water flow when operating and went on line to find the part.
I found it and then ordered it from partselect.com. I got it two days later. I looked at how the other part was connected to the hoses and reused a clamp. I recommend getting a new hose clamp to make fitting it faster. I felt great after I got it to work, so that we didn't have to buy a new washer (the part was only $26). I think that Repair should be added to Reduce, Reuse, and Recycle.

Unplug washing machine.
Disconnect water supply hoses.
Remove valve service panel, 1 screw.
Remove valve from panel with wires attached. 2 screws.
Remove water outlet hose from old valve.
Mount new valve to panel. 2 screws.
Attach water outlet to valve.
Move wires from old valve to new valve.
Dress wires.
Reinstall valve service panel, 1 screw.
Install new wire braded supply hoses.
Done. Hope to get another 20 years of service.

Washer is enclosed in a walled partition. I spent more time moving the washer out so I could get to the back of the machine. Due to Maytag's design of a removal sheet metal panel holding the valve the entire water valve replacement was performed outside of the machine. The replacement valve was an exact duplicate and made it a simple swap out. More time was spent removing inlet hoses and outlet hose then in actual valve replacement.

First turned off water and unplugged washer. Removed hoses and then removed bracket. The new part needed the bracket from the old mixer which was no problem - 3 screws. Removed electrical plugs from old mixer-placed on new one.No problems - worked like new. Thanks for your prompt shipment and the good illustrations of the parts when I was searching.. Also, half the price of local parts houses and it would still have to be ordered.

My husband did this repair. He disconnected the old part, laying them out in the order that he took them off. He put in the new part and hooked up the hoses and we had a working washer again. I ordered the part and a couple of days later it arrived on our door step. Thank you for your speedy delivery. We live in a parsonage and the washer & dryer that were in here stopped working, so we brought our Maytags (used) from our camp where the problem occurred because of winter freezing. Thanks to Maytag for making this repair so easy.

Did the same as others. Loosened the three screws diconnected the wires and put them on the new valve. Disconnected fill hose and connected to new valve. 10-15 minutes. Replaced panel and tested new part. perfect, My repair was a little longer, I vaccumed up all the dust bunnies I could find before moving washer back. Good for another 35 years, I hope. Thanks for the help and experiences.

Great service! Part arrived within two days; installation instructions very
clear; washer back in service after15 minute installation. Thanks!

Solved theprobel m by noticiing the HOT water filled the tub and it began to run when it was full. Figured out it was the solenoid valve. Ordered a new one. Simple to install and then it ran just fiine.