EF36IWFSS Refrigerator - Instructions

I simply replaced the drawer with my existing front. I received my order almost next day. I was surprised on their speed, loved it!!

Let me first say that I ordered this late in the day and it was here by noon the following day. I wasn't too sure on how to remove the front, white panel from the damaged crisper pan. While on the website, others had explained that you had to remove the white panel from the front of the drawer and did not mention any tools needed so I just snapped it off on the one side and then the other. I'm so glad I finally replaced the entire drawer as there were times when I forgot it was broken and many pieces of fresh fruit ended up on the kitchen floor.]Service was outstanding and will now order my icemaker for replacement.

The first thing I would like to say is thank you Parts select for a very fast delivery. It was within 24 hours I received my component. The installation went very well. The main thing is to take each part off the old mold, one at a time and install it onto the new mold. Make sure to look at each part as it is mounted to the old mold and re install them the exact same way. Just be gentle with some of the plastic pieces because they are fragile in certain areas. It will take a few hours for everything to start working properly. Thanks again Parts select. Good luck and God Bless.

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

i first removed the ice maker and took the motor assembley off. Right away i saw the problem. The wheel which drives the arm broke.
Once i get the new motor modl i just replaced it (it just pops into place with 1 or 2 screws).
put ice maker back in freezer and wola. Starting cranking out ice within 15 minutes.

Tough part was diagnosing the problem: bad water inlet solenoid, frozen inlet line, bad ice maker motor, or door opening sensor? Went to a parts shop & discussed the problem with the serviceman. He said you just need to sequentially replace each part. No way say I, that could cost $300 with a no-part return option.

I decided to replace the motor...Eureka!! It worked.
The underside of the ice maker cartridge has a plastic snap clip on either side of the cartridge. You need push each up, pull the left side of the cartridge out part way & disconnect the electrical connector on the right side(left..you facing the refrig.) With the cartridge out simply remove the 5 screws from the motor plate of the left side & replace with the new one.
Very simple. Slide the cartridge back in the frig. until the 2 snap clips click. Voila...you done! Cost $86..not $300. Apparently the motor is too weak to do the job & burns out quickly. Manufacturer should correct this defect.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

The minute my parts arrived, I took the drawer out, unscrewed three screws, replaced the side with the latch and then snapped the lid in place. It took 15 minutes and my fridge looks brand new.

Thanks so much for your speedy delivery. It was a great experience and I fixed it myself .

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

installed new parts

Removal of the Ice Maker required the removal of only one screw from underneath the maker and the power connector disconnect. Dis-assembly was straight forward. Remove old tray and heater, and reassemble with new tray and heater unit. Reinstall Ice Maker! Special Note: Allow the Ice Maker time to cycle through it's sequences. It may take a period of time before it starts producing ice after re-installation.

Checked if the cube maker still worked by putting some water in - yes!
Jumped the old valve to see if it would release water and nope.
Replaced the valve and everything is great.

You supplied the right part, the repair was simple and everything is working. No expensive repairman.

Opened up the door that covered the filter, unscrewed it and put the new one in and closed the door back up.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I removed three screws and replaced the part. It was very quick and easy>