Models > DWUA601AAB > Instructions

DWUA601AAB Admiral Dishwasher - Instructions

All installation instructions for DWUA601AAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DWUA601AAB
61-75 of 452
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Front door panel had scratches and dents from the wheelchair.

  • Customer: Nga from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Front Door Panel was replaced by unscrewing 3 screws on each left and right side of the dishwasher.

The bottom screws did not need to be completely unscrewed, just losen it enough to be able to remove the panel out.

Replace it with the new panel and screw back in the screws.

spray arm would not spin

  • Customer: Jay from Cardiff CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Even though there was plenty of water pressure from the pump, the lower arm would not spin. I could move it with my hand but there was too much friction for it to spin. Turns out an item named seal ring[38] (I would call it a slip ring) had become dislodged somehow at the interface between the rotating parts and the stationary parts but I did not learn that until I was able to disassemble it. I could see from the diagram that there were threads at the top of the SPRAY ARM SUPPORT[39] that engaged with the threads in the CENTER SPRAY NOZZLE EXTENSION[33] so I held the arm and tried to unscrew [33]. CRACK! The 4 thin plastic arms in [39] snapped right off. I then disassembled and found the dislodged seal ring[38]. I concluded that I would never have been able to disassemble without breaking [39] due to the calcium in the threads (even with repeated applications of vinegar or lime away): the plastic arms are just too wimpy. But the price of a new [39] was a bargain, I was amazed. Came in 2 days, I re-assembled, now the spray arm spins freely and the dishwasher works again. I will try to remember to use vinegar periodically incase the slip ring dislodges again. This has been a great dishwasher otherwise IMHO( and a bargain price).

dishwasher door leaking

  • Customer: JoAnn from Raleigh NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems.
I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in.
No more leaks!

leaking door- Dispenser Door Latch Grommet

  • Customer: Peter from San Jose CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Myscanning other reviews i saw mention dishwahser developed a small leak on RHS of door. I assumed the door gasket and planned to order that. On of the dispenser gromet which is only a $5 part so ordered that as well. I first replaced the door gasket which is an easy 10 mins job and ran the dishwasher again, but it still leaked.

I then removed the 7 torx screws on the door panel which came away easily. It was obvious that water was in there, so i removed the two screw on the dispenser with a nutdriver to replace the grommet. This process took 20-30 mins. After reassembly the leak was gone.

Without the comments on the website i would never have thought of the disepenser as source of the problem.

water leaked through front vent

  • Customer: mark from ardmore OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

Close door, turn on dishwasher, walk away. 5 to 10 min later dishwasher not running. Push in at the door latch and dishwasher would start back up.

  • Customer: Allan from East Bernard TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Removed the inner door panel-Removed the black cowling covering the timer and wires.
Removed the swicth assembly and installed new part.
Reassembled dishwasher.

I checked the operation of the two switches. One switch did not click, when button was pushed, as cleanly as the other. There was a bit of delay and play in the button when depressed, even sticking a bit.

Drain hose leaked

  • Customer: Mark from Mansfield OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 4 of 5 people found this instruction helpful
First I had to unhook the electric, water line and drain hose. Then slide out the dishwasher. Took several days to find the drain hose - local stores only carried a 6 ft hose and I needed a 7 ft. Once I found it online, purchased it and recieved it I put it all back together and all is good.

Water leak from the dishwasher door

  • Customer: Michael from Bronx NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

Leaking from the dishwasher on left side

  • Customer: Theresa from Zimmerman MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Took off the float, the jam nut was hard to get off, we ended up breaking the bottom piece of the float to get it off, but that was okay because we had a new float. The new float went on real easy and the jam nut went back on real easy. The foam insulation strip was real easy to get off we got a good hold of one end and striped it off slowly so there was nothing left on the door, then we cleaned the surface and put on the new insulation strip. We ran dishwasher to test it and there was no leak. Awesome. Cheap and easy to repair. We were impressed.

Leaking under door during wash and rinse cycles

  • Customer: James from Gulf Breeze FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Removed old gasket and foam strip. Cleaned area. Installed door gasket. Trimmed foam strip to fit and installed.

Leak has stopped!

missing screws for oven door

  • Customer: donna from baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Part did not come with corresponding securung hardware.

  • Customer: Ed from Skokie IL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 4 of 6 people found this instruction helpful
The replacement part was the perfect size but the threading on the terminal ends was increases to 1/2" v the 7/16" from the previous element. My first attempt was to find a similar type of part at the local hardware store(not a superstore)since I planned to replace the grommets anyway. After not having any success, I came home and modified the fasteners by slowly drilling out the id of the fasteners until they threaded properly. The time to replace after the drill out was less than 10 min and the ~$45.00 is significantly less than $450.00 for a new unit.
If I would ask anything of part select, it would be to include fastening hardware as re-engineering of products is a continual process.

Leaks out and below the front door

  • Customer: John Todd from Franklin WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

my silverware basket was broken

  • Customer: donna from houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
I reviewed the choices available, found what I needed, ordered it, got it (quickly), and dropped it into the dishwasher....happy happy!

Leak under dishwasher wash and rince

  • Customer: Richard from Edison NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 3 of 3 people found this instruction helpful
The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe
All Instructions for the DWUA601AAB
61-75 of 452