2202722-1-M-Whirlpool-Y913174-Motor-O-Ring.jpg
2202722-1-S-Whirlpool-Y913174-Motor-O-Ring.jpg

Motor "O" Ring

PartSelect Number PS2202722

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $4.51
  • You Save

    $.75
  • Your Price

    $3.76
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 1.9 / 5.0, 3 reviews What's this?
1-3 of 3
 

5 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerRon from Sandusky MI

Deteriorated (and leaking) impeller seal.

Dealer phone quote = $250. DIY repair = $55.
Turn-off DW electrical circuit breaker and shut-off hot water supply. Remove lower Front Access Panel and Toe Panel. Disconnect hot water supply, corrugated drain hose, electrical connection, and uncounter mounting brackets. Slide-out DW (being careful not to scratch flooring) and gently tip DW onto its back side. Rotate Ring-Lock at underside of Tub and (from inside the Tub) carefully lift out Motor-and-Pump assembly. At the Motor-and-Pump assembly, unscrew Center Spray Nozzle and remove Lower Spray Arm and lv Filter. At the end of the Impeller, remove Chopper Screw, Chopper, Chopper Plate (rotate 1/4 turn) and Chopper Wear Ring. Remove Motor Mount Screws and Motor Shield. Loosen Impeller {NOTE: left-hand thread} from motor shaft by the holding Motor Fan stationary and unscrewing Impeller. Pull apart the Motor and Impeller; discard old Impeller. Gently and thoroughly clean the internal surface of Housing Assembly seal with a toothbrush and soapy water. Carefully reassemble in the reverse order using the new Impeller. (Prophylactically, I also replaced the Motor "O" Ring and Pump Gasket.) DW works perfectly; no leaks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set, Wrench set

CustomerChristopher from Wichita KS

Water leaking from impeller shaft/motor seal

Remove the motor and impeller housing assembly from the unit by disconnecting the motor wiring plug, green ground wire, removing the drain and transfer hose, wash arm assembly and three screws for the filter assembly. A plastic locking ring secures the housing assembly into the unit and is removed by rotating aft about an eighth turn. The impeller is removed from the motor shaft by unscrewing the left hand threads on the fan that attaches to the end of the impeller. The impeller has longitudinal splines that engage the motor shaft, so it has to be removed by pulling straight off of the motor shaft. My impeller was stuck on the motor shaft, so I used a dremel tool with a cut off wheel and sliced through the impeller to loosen it. Installed a new motor shaft oring, and then slid the new integrated seal/impeller onto the motor shaft and secured with the fan (remember left hand threads). Reassembled unit and no leaks...

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Motor "O" Ring

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set

CustomerMilton from Fargo ND

Dishwasher leaked at pump housing

Unhooked the hoses and wires from the pump assembly, then took the pump assembly out of the dishwasher, took the pump assemby apart, separated the impeller from the motor. Put in new impeller with a new o ring on motor shaft. Since I don't have a repair manual i had to figure out each step. Then I reversed the order to put it back together. Ran it twice. Didn't leak. Put it back under the counter and ""buttoned it up.It took a Saturday to take it apart, I ordered the parts on Sunday. the parts arrived on Friday and I put it back together on Saturday. If you are not mechanically inclined you can still give it a try, the worst you could do is fail and end up buying a new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3