Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door would not stay shut
Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.
Removal of the entire 2 front panels Removal of the heat exchanger into the drum Removal and replacement of the belt Reinstallation of the heat exchanger, and both front panels
High limit thermal fuse blew because of lint buildup in discharge vent pipe
Opened things, saw lint buildup, cleaned inside of dryer, then cleaned entire vent discharge system, put new thermal fuse back, turned on dryer and heard metal to metal, opened dryer back up, saw missing glides (both gone). Ordered what I thought were 2 glides, 2 days later 1 showed, called and was told I didn't "update" when I changed order info (parts supplier cautioned to replace 2, should only sell in pairs) so then had to wait again for 2nd glide to show up. Replaced them today and noticed dried clothes are now cooler when finished. Will note in future if clothes are warmer, clean ductwork.
Just take the old parts with my tools and fix it, i did take the pulley bearing with care and put the new one, and adjust the screw on the motor base, the belt just was a little difficult but I did it, it's easy.
At the end of the drying cycle, the clothes had a bunt smell. I checked the lower compartment of the dryer and found the limit thermostat in two pieces and realized this could be the culprit. I was able to snap them together, but this did not work, therefore a new stat
First I unpluged the dryer, removed the two screws from the bottom access panel. I used a small socket to remove the screws securing the limit stat to the burner chamber, nut driver was too long. I installed the new limit stat with the two screws and attached the two leads. Plugged in the dryer and conducted a test run, burner ignited. I turned the dryer off and replaced the access panel.
At first i thought i had to buy new dryer, because i did not know what to do.I said, i never done this kind of repair before, well i put everything apart and notice that the idler pulley was worn out, then i said this is something that i can fix it if i get the part. I made several calls and couldn't find it. so went in internet and found it with you.
popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale
Squeaking motor, over heating, thermal switch kicking out.
Unpluged dryer from outlet, disconnected vent, positioned dryer on side, removed screws from bottom panel, pulled pannel away from dryer body to gain access to motor. Disconnected drum belt from motor pulley, disconnected wire harness from motor. Removed motor mounting bracket assembly and placed entire assembly on floor. Removed clamps and blower assembly from old motor, installed new motor and reassembled. Very easy project, hardest part requires some trouble shooting knowledge to determine the exact cause of problem.
I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.
I followed the instructions found on this site. The hardest part was figuring out how to release the clamps at the front of the dryer so I could remove the top.
The key was to unbolt the clamps at the back of the dryer first, then to use a putty knife to release the two clamps at the front of the dryer that hold the top to the front.
The rest was easy by following the steps already listed on this site and removing the two front pieces, then the drum and replacing the parts. Putting it back together was simple since I placed things in order and had taken pictures with my cell phone as I went through the process.
The time I took, included vacuuming the inside of the dryer thoroughly. Now it runs like new.
Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.
Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would cycle on once then wouldnt continue to heat to dry
I first unpluged the dryer then removed the bottom cover (two screws) then found the correct socket and removed the components and replaced them wire for wire. PLugged it back in and strated the dryer and watched the process. Unforunately it cycled twice and then stopped working. I went to a local appliance store to buy another high limit fuse because I thought it blew and happened to talk about the situation to a man behind the counter and he insisted it was the gas coils so I bought some and replaced them and its working fine now without replacing any more components. Im not a aapliance repair man but mechanically inclined but experience does pay. Hey, everything is easy if you know how...
My drier would start create heat,than stop heating after 8-10minutes.
After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!