Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replqce bad switch
pried old switch assembly from front of machine with screw driver. removed 2 electrical connections. shorted terminals to verify problem. inserted wiring terminals to new switch. verified operation and then pushed switch assembly into machine opening.
Old drum bearingwore out, squeeking like a banchee
Received part in two days. Removed inspection plate by removing two screws. .Drum bearing was right there. With screwdriver removed "c" clip, took out what was left of old bearing. With screwdriver aligned drum, slide new bearing into place. Job was done. Instruction with new part simple and easy to follow.
We ordered a new lint filter with white frame from Part Select. Had to take the dryer outside and blow all lint out that had accumulated in the dryer. We then vacumed everything out and brought back in house and put in new lint filter we ordered and used the dryer today and it works beautiful. Saved us from having to buy a new dryer. Thanks Part Select for having the filter we needed. Raymond Kampsen, Vassar, Ks.
Dryer making incredibly loud squeaking noise as it heated up
Replaced drum bearings, adjusted screw levelers trying to find the source of the noise. It was hard tracking it down. Finally lubricated the drum slides with WD40 and it resolved the problem for a couple days. Decided to try replacing the drum slides. The old ones did not look worn out - still had teflon surfaces - it was not metal on metal like I suspected. But when I got the replacement parts, there were 2 tubes of lubricant with notes that only this specific lubricant needed to be used on these slides. The teflon slides have a fiber material under them, and soaks up the lubricant. Problem appears to be solved. Whether it would be possible to purchase the lubricant only (since the slides looked OK) might be a question, however, the replacement kit cost was reasonable given that it solved the problem.
--Removed bottom rear panel (right under where 220 line comes in) which exposed belt and idler pulley. --Relieved tension on belt by moving idler arm and moved belt off idler puller (just to the side). --Removed e-clip. --Removed old pulley and washers. --Installed new thick plastic washer first, then pulley, then e-clip. --Relieve tension and place belt back on new pulley. --Replace back panel. -Fini!
Clothes pinching between the drum and door opening.
The drum slides on my dryer had worn down to the point that an opening formed that allowed clothes to enter the gap and get pinched between the spinning drum and the door. This would leave a mark and sometimes a cut on the clothes. To repair: open the door and undo the screws above the door opening that hold the top on the dryer. It's hinged in the back so it swings up from the front once the screws are removed. Undo hex head screws on either side at the top that hold on the front of the dryer. Also loosened the same at the bottom of the front panel (includes the door). Pull the front off of the dryer. This exposes the drum slides on either side in the front of the drum. They're fastened to the frame of the dryer. Undo the hex head screws (2 each) and remove drum slide, then replace. I recommend one slide at a time so the other one helps hold the dryer in place. The kit includes both slides. Pretty easy once I discovered how worn the old slides were! The drum turns much easier and quieter now too!
I checked the power (OK) and removed the four screws that held the timer/controls (upper panels) cover. This revealed a schematic for the dryer that enabled me to determine the door swich was probably the culprit. I pried out the old switch and, sure enough, it was always open (checked with multi-meter). I found the replacement switch easily using the dryer model number and "door switch" search string. Ordered Sunday night, the part came on Tuesday and took 2 minutes to install (no tools needed).
Simple - took out the defective filter and replaced with the purchased part. The hardest part was figuring out the right lint filter. The extensive info on PART SELECT was very helpful.
It was very easy. Pop out old, connect new wires and done! Can't say enough as to how fast and easy getting the part from this company was. Ordered the part later in the day one night and on the second day the part was there. Outstanding service.
Dryer was producing a screeching noise while running
I removed the front panel and the top of the dryer, pulled the drum forward and removed the old rear drum bearing then inserted the new rear drum bearing. I didn't replace the washers or the retaining ring in the back. Put the drum shaft into the new rear drum bearing. Put the front panel and the top in place and started using the dryer again.
The repair in retrospect was very easy. Not knowing alot about the dryer I made one mistake. I put the bearing in backwards and broke the rubber gasket. After ordering a new gasket and paying close attention to what I was doing it worked out fine. Saved me about $200 for a repairman.