D156B Jenn-Air Range - Instructions

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

After accessing the switch and removing the wires(four wires as the rocker switch operates both fan and oven light) I attached the wires to the new switch. However , I was unable to mount the switch in place as I could not get the spring - clip type of fasteners to slip on.
Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws
and nuts to hold the switch. The round-head screw
tops show on top of the stove, but at least the new switch is in place and operating.

Simple plug in.

needed hammer to help loose screws .pulled out and replaced leement

First, cut power to the range at the breaker box. I removed the jenn aire vent grill; removed two phillips head screws holding the switch bracket assembly and removed the switch assembly. After making a diagram of wiring, removed 4 bayonet type connectors. Next carefully remove the pushon nuts and save. Remove defective switch and discard. Install new switch on the two metal prongs over the black metal bracket making sure to orient correctly - use wire diagram and compare size of bayonet lugs for proper orientation. Push on nuts. Reconnect four wire bayonets; place switch assembly in proper position. insert and tighten the two phillips head screws that hold the assembly in place; replace vent grill and turn on power at breaker box.

Only problem was that new pushon nuts were too small for the jennaire metal prongs. Good thing i saved the old nuts!!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Installing the new switch was EASY. However, removing the old switch was very difficult due to the nuts holding the switch in place being designed as clamps not threaded screws and nuts.

The job was easier than I thought it would be. Turned off power at breaker first! Used phillips screwdriver to remove 2 fairly tight screws located on the vent side of the switch mounting plate. Flipped over plate and wrote down the 4 spade tip wire colors and location on switch. Removed the wires from the switch and removed the switch by prying off the locking washer with a sharpened/filed thin putty knife to get under it and then a flat blade screwdriver to finish removing it. Put the new switch in, hooked up the spade tip wires, mounted the plate back on and turned on the power. Worked great and I even impressed my Wife!

Cut power!
Removed old switch.Only problem was new switch had shifted the four 'spade' connectiors on back so when I was done fan and light switch was crossed.

Everything PartSelect had on their site was perfectly correct.

REALLY appreciated the way PartsSelect handled everything, I will be back for further help on other things.

Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.

Everything went fine. No trouble.

Removed top plate, disconnected old switch... Had to go to hardware store to get different push washers - the ones supplied with the part were too small. connected switch... tested connections and replaced top plate.

First checked to see if there was power to the heating element. There was , so I knew the element was bad. I ordered a new heating element and it came in 3 days! I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Reversed the procedure with new element. Turned on oven and my wife cooked a delicious meatloaf.

removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.