D156B Jenn-Air Range - Instructions

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

I got online, found this site, very easily found the part. The pictures were a tremendous help to ensure accuracy. The parts were delivered within 3 days without special postage. Without a doubt, I will order from here again!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

This same repair 2 years ago thru a Factory repair "professional" had cost $200. My cost $42.00!! Cost to replace the entire range...$1700.00.

removing the vent grid on top, by lifting off, then taking out the filter screen. removed the 2 screws on the back of the switchplate, then slide it back. made a drawing of the color wires and which way the switch faces... (it matters)
I took off the the old press-nuts by just breaking them with needle nose pliers. removed the old switch, fitted the new one (paying attention to where the little prongs and big prongs were on the old switch. used the nut-driver to press on the new nuts that came with the switch, and hooked back up the wires, and put it back.

We cut off the electricity to the stove before touching anything. We removed the 2 screws on the plate that is mounted to the inner wall of the oven. Then we pulled the element out 2-3 inches and disconnected the wires. We connected the wires on the new bake element and pushed it into place, inserted the screws and DONE!

The bigger part of the "repair" was the clean up of the fire extinguisher residue inside the oven due to the fire.

Turned of electrical power. Loosen two screws that held the stove top part that held the switch. Disconnected the old switch by removing the two clamps that held it in place, made sure wires were connected correctly on the new switch and used the new clamps to attach the switch in place. Put everything back together and turned stove power back on. Everything worked as it should.

Remove old filter- put in new filter. EASY!!!!!!!!

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294

Regrettably I have been unable to replace the bake element since the two screws are completely stuck. This doesn't appear to be a common problem.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

Removed old filter and replaced with new.