Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
really helpful site, FAST shipping
My oven would not work. It took longer & longer to fire, finally died. I did an online search & found partselect.com, with it's very helpful troubleshooting info, and somebody posted info that 80-90% of the time it's the ignitor that has failed. I ordered it Sunday night, it arrived Tuesday. I took the door off for easy access, took the bottom of the oven out, removed the flame shield and replaced the ignitor. I tested it and it worked! The hardest part was moving the stove away from the wall & threading the ignitor plug thru the back of the oven. The cheapest appliance repair visit would have been $89 + cost of parts. Sears charges $129. I think I saved at least $100, thanks to partselect.com.
The oven igniter lit up, but did not trigger the gas.
This website easily diagnosed the probable problem. We ordered the suggested part and my husband replaced it, despite a slightly eroded, rusted screw that was stubborn to remove, in about 20 minutes. The oven is working perfectly. With tax we spent about 50 bucks. I was sure we needed a new oven. We, ironically, celebrated by going out to dinner!
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
gas oven igniter would glow, but oven did not turn on
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out. Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.
Oven would not heat. Electronic ignitor (heating element) was not heating/not getting to temperature to open the automatic gas valve.
Make sure the knobs are all in the off position before starting the work. You may feel more comfortable shutting the gas valve off behind the stove or in the basement first, just make sure you fire the burner and let the gas that is left in the line burn off. Remove bottom pan in oven by sliding the pins (located in the back) towards you and picking up the back of the pan and pull it away from you, this will slide the pan off of the other 2 pins that you can not see on your end of the pan. Take the flare shield off from over top of the gas line (should be 2 nuts or 1 wing nut). Remove the screw or screws that hold the heat shield covering the ignitor wires and remove the heat shield. Unplug the ignitor. remove the screws holding the ignitor and remove it. Be sure to order the ignitor with the extra shield and make sure it has new screws, you may need to replace the screws. Try not to touch the element of the ignitor. it can be very brittle. It seems lengthy but is very quick and simple.
First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.
1. Turn off the gas (propane) 2. Unplug the oven. 3. disconnect the gas line and pull the oven out. 4. remove the back panel to access the igniter. 5 disconnect the igniter. 6. unscrew igniter/gas assembly and remove from oven (two screws). 7. unscrew igniter (two screws) 8. replace igniter with new. 9. reassemble in reverse order. 10. turn on stove. 11. Happy wife, happy life.
I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!
First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings
oven would not get hot would never turn on or turn on and never restart
Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great
