Models > CVG4380B > Instructions

CVG4380B Jenn-Air Cooktop - Instructions

All installation instructions for CVG4380B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CVG4380B
76-89 of 89
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

old burners wouldn't light

  • Customer: BOB from hartford KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
took old burners out, installed new ones . I was very easy and if i could do it anyone can. I used a rachet and thats the only tool i needed

Facelift

  • Customer: Mary from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We weighed the alternative of purchasing a new cooktop but we really like the Jenn-Air. We converted the Grill position to another two burner station. Parts fit perfectly. Re-used two of the Burner Brackets for the new burners. Installation was easy. Only down side was we continue to have problems obtaining the Grates. Did not ship as a two set kit as advertised. Not sure that was Parts Select's fault though. Only got three of the six replacement grates. Had to cancel and re-order. Although it was an inconvenience, the support staff were helpful. Has taken over a month now and still haven't received the grate kits. All in all though, it was an easy rebuild and Parts Select had all the necessary parts.

burner knobs were melted beyond repair.

  • Customer: Thomas from Tucson AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced the old knobs with the new ones.

The original filter was decomposing each time I washed it

  • Customer: Sharon from Kenai AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

only one burner on the cooktop worked

  • Customer: William from Chipley FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

Replaced Grill with two burners

  • Customer: Michael from Topsham ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Very simple project. Had no clue it was so easy! To test how easy it is, remove the left side grill parts, move the grill parts from the right to the left! I had no idea there was a micro switch in the cooktop to change the fan operation! Parts arrived quickly. Only received one grate of the set, this was quickly fixed by Parts Select Customer service! We only used the grill once, made such a mess! Why did I wait so long to do this! (Over thirteen years!)

One burner knob melted and one had a broken "stem"

  • Customer: Joan from Egg Harbor WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pop off the old and on with the new. Took longer to open the plastic packaging each came in than to remove & replace old knob with new.

Burner was not lighting

  • Customer: Luciano from Hollister CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

Nroken Burnner knob

  • Customer: William M. from Rock Hill SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slide the knob onto the shaft.

One set of burners would not ignite.

  • Customer: Brenda from New Market MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This range is about 17 years old and the igniter on the left set of burners had failed in the first month of use. A warranty repairman came, made a big mess, marred the adjacent counter top, spent a lot of time badmouthing Jenn-Air and left without fixing the problem. We have been manually lighting these burners all this time. Now that I am retired, I have set about repairing everything I can get my hands on just to have things to do. I always did this when I was young but got too busy with career and family. One big help is doing things now is you can Google a problem, find parts and instructions how to make the repair which is much easier than all the research you used to have to do. This repair is easy but time consuming due to all the screws that you have to remove to get to the igniter and the controller in the back. Since one side worked I was confident that the controller was good but the problem was only the igniter on the left side. This range is a dual fuel unit and has a downdraft connection so sliding it out from the wall is also time consuming. First pull the breaker at the electric panel. Remove the bottom plate and disconnect the flexible downdraft connection. Hopefully, you have enough flexible gas line so you can slide stove out to reach the back without having to shut off the gas and removing the connection. Next you remove the grills and burners. Then you have to remove all the screws connecting the top of the stove. There are nuts and washers that surround the gas jets that you can remove to partially lift the drip pan so you can unscrew the old igniter and install the new one. Next remove the back and see where the igniter control is located. Disconnect the old wire, install the new wire in the guides and insert in the controller. At this point all you need to do is put everything back where it was. This does not take a lot of know-how just time and patience. It makes you wonder why an "expert" could not have done this easily.

Filter worn out, exhasut fan kept going off

  • Customer: John from Cayce SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

range- top four burners will not light

  • Customer: Rick from Brockway PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed rear cover where the spark module was and change it

No spark at any of the 4 stovetop burners.

  • Customer: Ronald from Berkeley CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

rear burner not working

  • Customer: Larry from Washington NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
removed two hexigon screws--removed old burner---placed new burner into stove socket--replaced two screws. Done in about five minutes. Most time used to fine right size socket to fit screws! Fast delivery--easy repair--AND it works!
All Instructions for the CVG4380B
76-89 of 89