Models > CVG4380B > Instructions

CVG4380B Jenn-Air Cooktop - Instructions

All installation instructions for CVG4380B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CVG4380B
46-60 of 89
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner wouldn't light.

  • Customer: Clark from Tifton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.

switch too big for hole

  • Customer: Darrell from Moultrie GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.

Filter replacement.

  • Customer: Gerald from Maplefalls WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Remove and replace grease filter.

replace fan switch

  • Customer: David from Boone IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.

Old grease filter had hole wore through

  • Customer: Michael from Mountain Iron MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Pulled the old one out & inserted the new one. Less than five minutes.

Worn out stove top

  • Customer: Redona from Roseville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

vent fan cloging up

  • Customer: JAMES from McALESTER OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Fan on built in Jenn-Air went out.

  • Customer: Katrina from Coos Bay OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
ordered part, called friend who does odd jobs, and he came and turned off electric, unscrewed the area, pulled out old plug, plugged in the new. Turned on electric and walla, fan works !!!! thank you very much. Part arrived in very short length of time. I was surprised.

Fan stopped working.

  • Customer: Gregory from Hickman KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed the two screws that hold the switch in place. I then pulled the switch out about 3 inches and disconnected the three wires from the old switch and replaced the new switch....

it was painless

  • Customer: judy from clifton park NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
just as stated before. Remove old burners from plate and reattach new burners.

Filter needed replacement. Old one was falling apart.

  • Customer: Sophie from Warrenton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed old filter, dropped in the new one.
(This really was not a "repair")

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

  • Customer: Martyn from Middletown OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Needed to replace the grease filter!

  • Customer: Colette from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Followed the directions. Piece of cake!!

Old filter couldn't be cleaned

  • Customer: William from Goshen NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???

terminal spade wrong size on range wiring to fit module

  • Customer: wilber from oshkosh WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 7 people found this instruction helpful
cut off terminals and replaced with the right size one's stove lights every time now wlrowe
All Instructions for the CVG4380B
46-60 of 89