CSX25GPCCWW Hotpoint Refrigerator - Instructions

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

drawer rail broke about a year ago. repaired it with super glue. broke again recently. I would have replaced a year ago if I knew how quick and easy it was to get a new part. super quick shipping was excellent. had new rail installed the day after I ordered. Thanks

Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!

installed new dispenser control board. pretty easy. just make sure the actuater is snapped back properly or ice/water will not stop dispensing

Installed new replacement slide rail. Only two screws hold it in place. Very easy.

We received the part just a few days after ordering, unscrewed the old filter by hand, and installed the new filter the same way.

Watched PartSelect video and did exactly as video said. Had finished product in less than 30 minutes.6 bolts and one screw.

The vedio was great as a helping tool.Glad I got to watch it.

Per you video. Without it I would have probably taken a lot longer that necessary. You will never know how much I appreciate your including the video. What customer service. Outstanding.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen

First I watched the video and everything on that video was correct. I took off the hinge cap with a Philips screw driver on the top of the refrigerator. Then I took out two 5/16" screws with a socket wrench. Removed the hinge and the door lifted off. On the bottom of the door took out one screw and loosened the other one and replaced the Cam Riser. Put everything back together and it worked perfectly.

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.