CSK27PFXAWW Hotpoint Refrigerator - Instructions

I was astonished when my part (PS306943 SLIDE ASM LH (Drawer Slide Rail - left side)arrived the very next day!!
In a big box, beautifully wrapped.
I got out my screw driver, detached the dead shelf support and screwed in the new one.
Oh it's so very nice to have the fridge working again, and so soon.
Hooray for Part select.com
The best thing since sliced bread.
Jill

Removed 2 screws on each slide, Screwed in new slide. Done! The hard part was picking the correct part #. Ordered the wrong parts. Parts Select representative helped me get the correct part # and assisted with the return. Thanks.

Emptied the ice from tray.
Removed the four screws that hold the face plate.
Removed the four screws that fasten drive housing to the tray.
Slid the drive cup into place at the end of the auger.
Made sure the rubber gasket was in place .
Replaced the four screw that hold the housing to the tray.
Replaced the four screws that hold the face plate.
Put some ice cubes in the tray and tested to be sure everything worked properly.

Found your web site and bought a couple of replacement parts from you guys and reaaembled unit. Its now working. Only issue I had was in the reassembly of the auger unit, wasn't quite sure of the blades etc. and the proper order Saw the sketch on your site and figured it out from that. Will visit you guys again when I need a part. Good delivery and timely. Thanks and regards Gil

Removed the broken rail by removing two screws. Put one screw through the hole in the new rail, matched it to the hole in the side of the fridge, and tightened it - not too tight! Then guided the second screw into place and did the same thing. Replaced the drawer. Job done.

Identifying the part on the website was a breeze too, thanks to well-organized site, a picture of the part to match to my broken one, and even a video of a repairman making the repair. Couldn't have been easier, and probably saved me about $100.

Not really a repair. Just dropped it into place.

Would recommend this site to others ... comprehensive parts and descriptions, easy ordering and timely delivery.

Thanks much!

we took off the old one and replaced it.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

After contemplating for months on replacing my GE side-by-side refrigerator and realizing the only reason I wanted to is because the door handles were disgusting, I found this site and decided to try to replace them first. After reading other instructions shared, it was a relatively simple fix. You'll need a flathead screwdriver to pop off the trim and a torque screwdriver to remove and reinstall the handle screws. That's it. Looks great! Wish I would have done this sooner as it would have saved me a lot of worry time. The cost of replacing my refrigerator is a nice perk, too!

SNAPPED THE NEW SHIELD IN PLACE. DONE!

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

The gasket I received was stated to supposedly fit my refrigerator, and the box even had printed on it that the gasket was magnetic. However, after going through the difficult process of removing the old one and installing the gasket that was sent me, I discovered that the new gasket WAS NOT MAGNETIC, and would not keep the freezer door closed. I repaired the cracked area on the old gasket and reinstalled it on my refrigerator. When I called Part Select to return the defective part, I was given every excuse in the book, including that the gaskets aren't made with magnets any more, even though the box stated it WAS SUPPOSED TO BE MAGNETIC......just like I was supposed to GET RETURN INFORMATION BY EMAIL that I have never gotten, and my emails are ignored as far as returning it. I WILL NEVER PURCHASE FROM THIS COMPANY AGAIN....

took the old off and replaced with new one very simple . new snapped into place

The internal water line was leaking. I could not find any repair parts for my refrigerator but the GE 5/16 water line was the same size. I purchased 6' of tubing and two unions. Make sure the clean and square. If possible, make the cuts in a spot where you can use the pliers and wrench to tighten the union. I cut approximately 2' out of the existing line and replaced it with the same length of new line using the 2 unions, one on each end. Took about 5 minutes.

I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.