| |
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerPatricia from Tampa FL
Previous glass cover broke during cleaning
Removed 2 Phillips head screws and replaced rail. Glass cover does not fit on rails perfectly, but solved the problem.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRonald from Reidsville NC
3 of 4 slides were broken
Removed 2 screws on each slide, Screwed in new slide. Done! The hard part was picking the correct part #. Ordered the wrong parts. Parts Select representative helped me get the correct part # and assisted with the return. Thanks.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers, Wrench(Adjustable)
Customermiguel from lawton OK
Broken drawer slide rails, actuator pad worn out, double outlet water valve inop.
moved refrigerator away from wall and unplug it from electric outlet, turn water supply to the Water Valve off, removed 4 screws that hold refrigerator back cover, move cover out and removed water supply line from valve, removed 1 screw that hold the Outlet Water Valve and remove it slowly until you can disconnect electric wires. Cut plastic water lines with box cutter or cutting tool at the valve. To install push water lines into new valve, they will selfsecure, each one is different size and there will be no confusing which one go where, if electric plugs are diferent, adapter are provided, just plug them in and the plug in electric wires and then reverse the the order of disasembly to finish. (hint, before installing back cover check for leaks).
the slide rails are very easy to replace, just remove the old one with a cross tip screwdriver and replace.
actuator pad was very easy to replace, pull old one out and push new one in place.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerTom from Coto De Caza CA
Both left side drawer slides were damaged or missing.
Really easy. I am the type that measures once and cuts twice! But this time even I could do it. The hardest thing for me was locating a phillips head screwdriver in the house. I ordered the correct parts, thanks to the diagram provided, and followed the easy directions. It went exactly as expected.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Left Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerPhillip from Rapid City MI
The slide rail has been broken for several years.
Remove and replace two phillips head screws. Finished! Why didn't I do this years ago. It took longer to clean out the vegie crisper than it did to replace the slide rail.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Left Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDonald from Corbin KY
Left side rail for drawer was broken
I removed the two Phillip's screws holding the old slide and removed it from the compartment. I placed screw into back mounting hole and partially tighten. Next I swung the slide up till the front hole matched the hole in compartment wall and installed this screw. I tightened both screws and returned the drawer to the refrigerator.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Drawer Slide Rail - Left Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJim from Huntsville AL
Meat storage drawer rail broken
First of all, the Parts Select response was extremely quick. Would order parts from them every time. The installation was removing two screws and broken part while replacing with the new one. Quick easy no problem.
|