CSK25GRYEAA Hotpoint Refrigerator - Instructions

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Two screws held the drawer slide. After taking everything out of the bottom of the fridge (and cleaning the grunge that had accumulated under the drawer), I took out the two screws, removed the broken slide, put in the new one and was done. The installation was far quicker that cleaning the gunk in the fridge! As to the dairy door, no tools were needed. It just popped straight into place. The parts came VERY quickly and were exactly what I needed.

It was a tough job to replace the drawer slide rails at the bottom of the refrgerator on both the left and right sides. I had to get on the floor on my knees and stomach to get my head inside trying to see the work to be done. First the screws from the broken drawer slide rails had to be removed. The screws in the front part of the rails were a little easier than those in the middle. (Fortunately, there were none in the back.) The screws are hidden in cylindrical grooves and one can't get its head in far enough to see. The middle ones are extremely difficult when on your kneees and stomach. Using a trouble light inside helped a little. The screws in the middle were really tough especially inserting and starting the turning, both in loosening and tightening. Fortunately, I had long nose snips that allowed me to brarely grab the end of the Philips screws and gently insert them in the grooves. Then with luck in aligning the sacrews. I was able to start the tightening but had to use my left hand on the right side as there was no room for my right hand. The total job took a few hours of struggle but I finally finished the job and it was perfect. If I ever have to do it again, I'll know the procedure better. The completion of this task gave me great satisfaction. I think my description here is probably more than neeeded.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Undcrewed broken parts (2 screws each) and replaced with new parts and screwed them back in place,

Removed everything from freezer, Removed back panel, defrosted coils. removed thermostat top left, cut wires and used heat shrink to splice back together, clipped thermostat back on. I actually replaced the defrost timer and defrost heater also. Best bet is to do all 3 at one time. Part Select will have the new parts to you in days. Great Service and the online repair man is great. I saved hundreds of dollars doing myself.

Purchased two new drawer slides and installed in less than 5 minutes. 2 screws on each side. Extremely easy

I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.

Remove ice maker bucket. Unscrew single screw in center of shield, take out shield. Insert new shield, making sure the 2 tabs on the shield are slid into mount from the left, center the shield so center tab is aligned with screw hole, Tighten screw, replace ice bucket. SUGGESTION: This would be a good time to replace light bulb!

I removed the ice container with the auger inside. I removed the front panel, then the auger and housing. I had to clean all of the parts that had rust on them. I got some of the parts mixed up and was having a hard time putting them back where they belonged. I went back on the PartSelect web site and with my IPad and opened the exploded view of the parts. This enabled me to put the auger back together. It works perfectly now. Saved a lot of money by doing it myself. Thanks PartSelect.

The Hinge Cam Riser came as ordered and arrived in 1 day! The original riser was clearly broken in half. After installing the new one on the door hinge and adjusting it several times, the door closed a little but still didn't close all the way. Finally, I re-installed all the door trays and filled them with the usual perishables, and the door closed perfectly! Apparently, the extra weigh on the door was needed to complete the job.

Empty all the good stuff stored in the door. Remove top hinge, lift off door. Remove bottom hinge from door and refrigerator, replace with new hinges. Replace door and reinstall top hinge. Very simple. Worst part was removing all the stuff stored in the door then putting it back! My parts arrived very quickly and I'm very pleased with Part Select.

With my wife's help, we emptied the door shelves and removed the door to the kitchen table. The video and instructions for replacing the parts were 100% right. We probably spent more time cleaning the door bottom and gasket than actually changing the hinge assembly! The job went very smoothly and saved us from overspending on a repair to this old fridge, or worse, making a quick decision on buying a new one.

I viewed a how-to video on partselect.com. I removed all items from the door shelves. Used a screw driver to remove the top "hinge" plate. Used a nutdriver to remove the door hinge plate. Removed door, laid on it's side-hinge side up (if you don't have a helper, lay it on a flat service). Simply removed the broken bottom plate and replaced with new part, and reinstalled on refrigerator. Super Simple!

Ordered new Ice Maker from you and fixed the problem completely.