Models > CSK25GRYEAA > Instructions

CSK25GRYEAA Hotpoint Refrigerator - Instructions

All Instructions for the CSK25GRYEAA
496 - 509 of 509
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Parts Used:
Dispenser Door Assembly or Flapper
  • David from Kennesaw, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
actuator pad it was broken
just i took off the actuator and replace with the new one in 8 minutes.It was so easy.
Parts Used:
Actuator Pad
  • JULIO from LOS ANGELES, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Parts Used:
Dispenser Door Assembly or Flapper
  • Richard from Dumfries, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The refrigerator door would not close on its own because the cam was wore out.
I just followed the video instruction supplied by PartSelect and the whole thing was a breeze.
Parts Used:
Bottom Hinge Assembly
  • ANTONIO from LUTHERVILLE, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Freezer door hinge.
Removed freezer door, put a blanket over the opening to keep food frozen. Installed hinge and replaced door.
Parts Used:
Bottom Hinge Assembly
  • Mitchel from Onley, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Pad had worn thru after years of use
the pad is a slip in I just used grease to allow for the friction and had it in with in a minute
Parts Used:
Actuator Pad
  • dennis from Palm Desert, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Refridgerator door was not closing properly
Followed the u tube video that was on the Part select website. Very easy install when following the video.
Parts Used:
Bottom Hinge Assembly
  • Tim from New Berlin, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Icemaker would only make crushed ice, no cubes
I first replaced the ice bucket which allowed the auger to turn but did not fix the problem. I then ordered a new solenoid and plunger and after installing them it now makes ice cubes. Problem solved.
Parts Used:
Ice Dispenser Bucket Ice Bucket Seal Ice Dispensing Drive Cup
  • John from Snellville, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
frost formed because the ice damper let warm air into the freezer
Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.
Parts Used:
Dispenser Door Assembly or Flapper
  • jon from social circle, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
We had ice crystals on the ice tray and door
Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)
Parts Used:
Dispenser Door Assembly or Flapper
  • Theresa from Grand Blanc, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
leak causing ice build up in freezer compartment
I had to defrost large chunks of ice from the rear of the freezer compartment and tried reactivating the ice maker several times before deciding to order the replacement fill tube grommet and clamp. This was very stressful and complicated to accomplish while trying to avoid food spoilage, and consumed a lot of time. It involved removing the ice maker and various panels, plus disconnection of 2 electrical plugs, then using a hair dryer to melt ice build up. The installation of the new parts was quick and simple once they arrived in the mail, and this appears to have solved the leak problem. The fill tube slides easily into the grommet and the clamp, tightened with a screw driver, secures the water feed line on the other end. Fill tube must be carefully threaded through rear panels and into the ice maker receptacle and the grommet needs to be pushed hard and wiggled in order to seat properly in the rear surface of the refrigerator.
Parts Used:
Fill Tube Grommet Fill Tube Clamp
  • Albert from New York, NY
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Flapper became warped. Freezer /icemaker frosting up... ice melting and sticking.
Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !
Parts Used:
Dispenser Door Assembly or Flapper
  • Jeanne from Amissville, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door flapper to ice needed to be changed
Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.
Parts Used:
Dispenser Door Assembly or Flapper
  • John from Ocean View, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door Wasn't Closing All The Way.
Did the repair jut like the instructions on the web site stated. There was a good video for doing this repair. Looked at it a couple of times and did the repair right off the bat. Thanks folks.
Parts Used:
Bottom Hinge Assembly
  • John from Valdosta, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CSK25GRYEAA
496 - 509 of 509
Back to Top