CSD2122ARW Magic Chef Refrigerator - Instructions

Pretty simple really...take out a couple screws and the face plate comes off. Take out the dispenser apparatus behind the face plate and you will see the little lever operated switch that activates the dispensers. Mine had one terminal slightly discolored like it got hot...so that is a good clue. Also, the whole system is pretty simple really, and the switch was clearly the culprit. I got the replacement switch from PartSelect in just a few days, and put it in. The whole deal only takes about 1/2 hour cradle to grave. The dispensers work fine now, and I think I saved at least $150 for a service call. BIG PAPA small

The ice maker was easy but the older Maytag inlet valves are rigid plastic line- make sure that line is properly connected to back of fridge- the 1st night the water leaked down back of freeze- thus no ice in ice maker tray ----but the bottom of freezer was full of frozen water--- took ice maker off and realigned inlet pipe- once that was done- no more problems- ( did also have to take hair dryer and remove all ice build up in bottom of freezer --- remember to check that rigid line as it can become detached while changing out ice maker assembly- thx Greg

Shut off water and unplug fridge. Remove ice drawer. Unscrew one short nut underneath icemaker, and the two longer ones holding it to the wall of the freezer. Now remove white cover. It just needed a little jiggling w a flat head screwdriver to loosen it. Now you can see where the wire harness is connected, use the same flathead to depress the plastic pin holding it in place, and slide it out. Remove the wire harness from the metal clip on side of icemaker. Now you should be holding the old icemaker in your hands. Remove the bale carefully. Now install the bale into the new icemaker, while making sure it's in the 'down' or 'on' position. Bring the new icemaker into position, gently snap the wire harness into place, sliding the wire into the clip like it originally was. Fasten the three screws again. Then, finally, snap the white cover back into place. Slide the ice drawer back into position, turn on the water, plug the fridge back in and wait 30-45 minutes for your first batch of new ice cubes.

I watched the video on how to change the ice maker, very easily explained, and removed the old in about 10 minutes.After seeing how the old one came out it only took five minutes to install the new one. The appliance repaircompany wanted$120 just to diagnose the problem,i bought the part from partselect for$104 total. This is the forth time I've used this site and saved a ton of money.

easy, followed instructions and installed new parts.

pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

Disconnected power--removed ice holder tray--removed ice maker end cap--disconnected electrical wires--removed one screw holding ice maker to refrigerator--lifted up on ice maker to remove it from two holders--took control wire from old icemaker and installed it on new one--reinstalled new icemaker in reverse order.

Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Watched the video and followed the instructions ... time to repair was slightly longer than expected due to the fact that my fridge had wood panels requiring removal. Still, the video was terrific since I am a visual type person.Part Select service was amazing ... ordered one day and the part arrived at my door the very next day. Had the same type of service on a previous repair to replace the ice crushing part of the ice maker. What a company!!! Thanks so much.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

I shut the water valve and bled the pressure off by using the water dispenser. Removed the four screws that hold the cardboard backing on the unit. Unplugged the power cord, loosened the metal water supply fitting. Then I removed all three hose fittings and dried the drips with a towel. I pushed the electrical plugs off with a flat blade screw driver. Removed the bracket attachment screw and pulled the double valve out. The new valves came with a push-lock fitting for the plastic hoses so I pushed them into their sockets. Put the new valve in and replaced the attachment screw. Reattached the water supply line and the electrical connectors. I turned the water on and checked for leaks. replaced the cardboard backing, and plugged the power cord back in.

1. Viewed the video furnished (very helpful) 2. Turned off circuit breaker (avoids having to move the refrigerator), took my chances and left the water on 3. Removed the ice bin 4. Removed bottom retention screw, loosened the top two screws 5. Lifted the old ice maker free of top two screws 6. Used the bright flashlight to see how to release the rear electrical connection 7. Placed old unit on toweling, removed the electrical harness, the bail and the lower retention offset bracket (needed because the Kenmore's bottom retention is toward the center of the ice maker) and reinstalled them on new unit, taking care to maintain the original harness clip method 8. Carried the new unit to the refrig and installed the rear harness connector, then lifted it to mount on the top screws, forced it down to correct position, installed lower screw and tightened all three. 9. Placed bail in 'Operate' position, Installed bin and turned on the power. 10. Next morning, success!

removed the back cover unplugged the unit removed the old fan blades installed the new easy to pull off and easy to install

I followed the directions from the YouTube video, which were spot on correct! Loved it. No problems. I did have to wind the spring one more turn than it showed on the video, but that was easy to figure out. No problems!