Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS395284
This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forced-air cooling for the condenser coil.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Unplug the appliance.Removed the screws holding the back panel.Removed the fan blade.removed 3 screws holding the condenser fan.Remove the 3 metal brackets attached to the fan.(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)Cut and strip the wire about two inches from the fan.Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)Screw the back panel back on.Mount the new
Help other customers find the most helpful instructions.
Were these instructions helpful?
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.
First I unplug the refrigerator, then I unscrewed the cardbord cover with a screwdriver, disconnected the wires, unscrewed the screws, removed fan bracket with the fan. Since my wire connector was different, I had to strip the wires to connect the fan, twist wires together with the connecting wires, use wire nuts wire nuts and wrapped in black tape. I then hooked together the connection making sure the fan was rotating in the right direction. I then placed the fan bracket back in its place, lined up the screwed holes and installed the screws back to the original tightness. I plugged the refrigerator up to see if the fan was working properly. It was so I unplugged it again to start the nwxt part replacement.The next part I installed was a icemaker and water dispenser water inlet valve. I turned off the incoming water valve. I removed the two screws that held the old water valve in place. Unplugged the two connectors, removed the water lines and reinstalled the new water inlet valve hooking it up the way I unhooked it. Then I turned on incoming water line, checked for leaks. I put the cardboard panel back on and was done. The two parts were successfully installed in an hour. We now have a efficiently working refrigerator and a cold freezer and have the proper amount of ice cubes that are supposed to be made.
Remove the back hardboard cover screws for access to the condenser fan. I opted to tip the fridge over on its side for even better access to the fan mounts and wire. Replaced the fan assy (reused the fan). Splice the wire and it's done.
After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Removal of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.
My husband replaced the condenser fan. It took awhile and a few choice words but he got it replaced. The fan seemed to work fine, but it still wasn't cooling. I noticed that when we had the fridge unplugged that water started draining out the dials at the top of the fridge under the freezer. And there was absolutely no water at all in the drip pan under the fridge. So I took the doors off and totally took the inside of the freezer apart. I discovered that the styrofoam on the floor of the freezer had become inudated with fluid and the under the foam the coils were all frozen solid with ice. Hence not allowing any drainage. I put a lamp in the freezer area and defrosted all the ice. In searching the internet i discovered that they no longer produce the foam so i went to home depot and got a piece of foam and aluminum foil and cut it to replace the ruined foam. I put the fridge all back together said a prayer and crossed my fingers and lo and behold it works perfectly now!!!!
Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.
The motor kit had only two wires coming out of it. The existing one in the refrig had 6. I spliced the 2 red to one black on the new part and 2 white to the other black wire on the new part. The two green I attached to a screw. I left the 6 wire harness in place just cut off the plug piece that went into the old motor, and spliced all my wires. Worked great!
While investigating a water leak I discovered the condenser fan seized. I removed the fan to prevent a fire and ordered the part. The hardest part was identifying the correct fan. That took longer than the installation. I cut the wires and spliced in the new motor. It rotated correctly and I replaced the crill. Done Total time of ice maker water leak repair and fan replacement about 1 hour.
UnplugRemove entire back panel (both chipboard and metal fan grill)Unscrew both fan mount plate screws - fan won't be able to come out because it is still plugged inWhen looking at back of fridge, locate a small plastic box to the immediate left of the condenser. It's a circuit block. Release the metal spring clip holding the plastic cover in place, and trace the fan wire connections back to the fan. Make a note of which wire is connected to which terminal (1 of the fan wires has white lettering and 1 is just black)Unplug both fan wire connects from circuit block to release the fan power cable.Remove the fan mounting plateRelease fan blade clip by pressing fan against motor and unscrewing and remove fan bladesUnscrew motor from brackets - note alignment of motor on bracketsMount new motor on brackets. Leave plug wire disconnected (replacement motor has a harnessed plug wire)Connect new plug wire to the circuit block keeping wires connected to the proper terminalsSnake new plug wire behind condenser like the old wire was and run through cable bracket to the back right of the condenserPlug wire harness into motor and re-mount fan mount plateReattach fan blade and secure using blade mount kitReplace back panels
1. Removed the cardboard cover.2. Removed the terminal block and unplugged the old motor.3. Removed three screws that held old motor to the bracket.4. Removed the fan blade from the old motor.5. Installed the fan blade (after cleaning) to the new motor.6. Crimped on new wire terminals onto the leads on the new motor.7. Installed the new motor using the fasteners provided.8. Plugged the new motor wires onto the proper terminals in the terminal block.9. remounted the terminal block.10. reinstalled the cardboard cover.
simply removed old motor and replaced new. I'm over 82 and it was hard to get down and up to floor level!! One thing was a little puzeling -that was to insert the right screws which had a nitch in the end of the threds to keep it from loosening- I thought I was spoiling the threds cause I had to use a little pressure to start the screws and thought I had the wrong screws--they had sent several sets of them for different name brands- but II got it and everything seems to be allright - Could you tell me if I could purchase a replacement compressor and some refrigerent -the new kind. thank you, George Erlandson Only if my comp. goes out!!!
My refrigerator condenser fan was burned out, and it was so weak you could stop it with your hands, and over time it will stop working.I order a replacement and change it my self, all you got to do is take the cover from the back off and unscrew the fan + blade it was like 3 screws; I did had to cut the wires because the original fan had a connector the replacement did not had, but that was no biggie, it all works now it's been over a week so I call it a success.
I saw on a partselect web site that these symptoms could be caused by a failed condensor fan motor. After removing the cardboard panel in back of the refrigerator I noticed the fan was not running when the rfigerator was. The fan was held in place by three brackets. I unscrewed the screws holding the fan motor to the brackets and also unscrewed one of the brackets to make room to pull the motor out. I cut the wires close to the motor. I removed the fan blade and secured it to the new motor. I had to reroute the old wires in order to have enough slack to use wire nuts to attach them to the leads on the new motor. I then re-attached the motor to the two brackets remaining in place and then re-attacehed the third bracket I had removed to get the motor out.. The most difficult part was working in a very confined space.
I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.