All Installation Instructions for Maytag Range CDE852

old part lasted more than 20 yrs so needed to replace

just replaced by hand .

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Anjali from TALLAHASSEE, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner plugs were loose

used the supplied parts...very easy. The parts were exact replacements.

Parts Used:

Surface Burner Receptacle Kit

James from CONCORD, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced grease filter

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.

Parts Used:

Grease Filter

Light Bulb - 40W

Gregory from CARMEL, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

filter was deteriorated from 15 plus years of use

lifted the top center panel off removed old filter installed new easy peesy

Parts Used:

Grease Filter

Steve from Marshall, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Grease filter clogged and in need of replacement

EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.

Parts Used:

Grease Filter

Mark from STAUNTON, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old one was plugged

Pulled out old one and slipped in the new one.

Parts Used:

Grease Filter

Rudy from GARIBALDI, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Jennair cooktop with coils lost one of its coil guides.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

Parts Used:

Surface Burner Receptacle Kit

Bruce from SOUTHBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My electric range burner was not heating.

All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.

Parts Used:

Delta Frame Surface Unit - 8 Inch

Joyce from Oceanside, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wire came loose and shorted out

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Parts Used:

Main Power Terminal Block

Elizabeth from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The radiant ring element had broken

Removed old element, plugged in new one, tested ok

Parts Used:

Delta Frame Surface Unit - 8 Inch

Martin from Alexandria, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

stove top burner would not heat

new element plugged into burner connection- an easy fix

Parts Used:

Delta Frame Surface Unit - 6 Inch

Marjorie from Indianapolis, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I snapped a bolt on the main power terminal block when connecting the pigtail.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Parts Used:

Main Power Terminal Block