BSS25GFPHCC General Electric Refrigerator - Instructions

I watched the videos before I received my parts. I thawed the freezer out, removed the panel in the back. Cut the wires to the defrost thermostat and spliced the new one on with wire nuts and tape. Then I did the same for the temp. sensor. Put it all back together. Now the freezer isn't running all the time. I set the temperatures back to normal and it seams to be fine.

I replaced both the Defrost Thermostat and the Temperature Sensor located on the top of the cooling coils. I ordered them because they were the least expensive items that addressed my problem. They did not correct my problem. I then ordered the Main Control circuit board. I installed the board in about 15 minutes. Finally my freezer returned to the set temperature of 0 degrees F. Problem solved

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

The video instructions were easy to follow as well as the replacement. The replacement Main Control Board is generic to different refrigerators and has more connectors than the original. Be sure to identify the locations prior to removal and installation.

Ordered the part, watched the video, did it, ice maker worked....very easy. Thank you.

I pulled cover off back that housed the board. Unplugged all the wires that went to the board. wires will only fit in one spot so you cannot mess it up. snapped it off the pegs, then replaced new board in same spot. hooked plugs back up and installed ground wire. covered it back up plugged it in and it ran.

Replacing the motherboard was really easy. However it has not fixed my refrigerator. I continue to have cooling issues with fridge and sometimes with the freezer.

Part received in two days,installed in 5 minutes.Thank you.

I'm a housewife in her late 40's. Before ordering the part, I watched your video on how to remove and install the new icemaker. First I unplugged the refrigerator. After a few minutes, I unplugged the icemaker and unscrewed it. I lifted it a bit and removed it. I did not use the icecup that comes with the part. Instead I removed the one from the old part and inserted it to the new one. Then I plugged in the new icemaker, placed it inside so as to match the holes and screwed it in. YES, it was that simple. It took me less than 10 minutes to do this. I saved myself over $100!!

The repair was quite easy. The installation video on your web site was a lifesaver. Without your video the installation would have been far more difficult.If you are doing this repair watch the video,it will save you a lot of time and potential problems.

Just like the video show on the wed site.

Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.

Watched the video from your site and followed instructions, extremely easy after that.

After pulling fridge out from the wall, removing the bottom back panel and inspecting the fridge operating parts, I noticed the condenser fan never comes on. Reading online I found that most of the time the problem is with the main control board. I simply unscrewed the back panel, carefully disconnected the cables from the old board, plugged them back in to the new board, replaced the panel and started the Fridge back up. It cooled right down to normal temperature within the hour! Five years of neurotic behavior around cooling the fridge were over! My wife and I constantly rearranged various fans around the kitchen and joining rooms, opened the cabinet above, taking out the bottom shelf to make more ventilation, pulling the fridge out from the wall several inches, and worrying every time the freezer went up to 9 or 10 or even 20 degrees, and the fridge section up to 40 or even 45 degrees F. I can sleep easy now, and use the fans on us in hot weather, rather than the constant buzz in the kitchen. We can even have a conversation without yelling above the din of the fans!

Took old part out, put new part in. Thats not the story here, it was the ease of finding the part needed, the price was very reasonable and the service was second to none! The part arrived in less than 48hrs. (no special shipping was used) I would like to thank the people at PartSelect for a great experience. Other companies I have delt with in the past could take a few lessons in customer service from PartSelect. I highly recommend them! Patrick Spinks